- 您现在的位置：买卖IC网 > PDF目录80549 > M34509G4HFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24 PDF资料下载
参数资料
| 型号： | M34509G4HFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| 封装： | 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24 |
| 文件页数： | 104/143页 |
| 文件大小： | 1056K |
| 代理商： | M34509G4HFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页当前第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页
4509 Group
Rev.1.03
2009.07.27
page 63 of 140
REJ03B0147-0103
Multifunction
- The input/output of P00 can be used even when SIN is used. Be
careful when using inputs of both SIN and P00 since the input
threshold value of SIN pin is different from that of port P00.
- The input of P01 can be used even when SOUT is used.
- The input of P02 can be used even when SCK is used. Be careful
when using inputs of both SCK and P02 since the input threshold
value of SCK pin is different from that of port P02.
- The input of P11 can be used even when CNTR1 (output) is se-
lected.
The input/output of P11 can be used even when CNTR1 (input) is
selected. Be careful when using inputs of both CNTR1 and P11
since the input threshold value of CNTR1 pin is different from that
of port P11.
- The input of P12 can be used even when CNTR0 (output) is se-
lected.
The input/output of P12 can be used even when CNTR0 (input) is
selected. Be careful when using inputs of both CNTR0 and P12
since the input threshold value of CNTR0 pin is different from that
of port P12.
- The input/output of P13 can be used even when INT is used. Be
careful when using inputs of both INT and P13 since the input
threshold value of INT pin is different from that of port P13.
- The input/output of P20, P21, P30, P31, D2, D3 can be used even
when AIN0–AIN5 are used.
Power-on reset (only for H version)
When the built-in power-on reset circuit is used, set the time for
the supply voltage to rise from 0 V to the minimum voltage of rec-
ommended operating conditions to 100 s or less.
If the rising time exceeds 100 s, connect a capacitor between the
RESET pin and Vss at the shortest distance, and input “L” level to
RESET pin until the value of supply voltage reaches the minimum
operating voltage.
POF instruction
When the POF instruction is executed continuously after the EPOF
instruction, system enters the RAM back-up state.
Note that system cannot enter the RAM back-up state when ex-
ecuting only the POF instruction.
Be sure to disable interrupts by executing the DI instruction before
executing the EPOF instruction and the POF instruction continu-
ously.
LIST OF PRECAUTIONS
Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.1 F) between pins VDD
and VSS at the shortest distance,
equalize its wiring in width and length, and
use relatively thick wire.
CNVSS pin is also used as VPP pin. Accordingly, when using this
pin, connect this pin to VSS through a resistor about 5 k (connect
this resistor to CNVSS/VPP pin as close as possible).
Note on Power Source Voltage
When the power source voltage value of a microcomputer is less
than the value which is indicated as the recommended operating
conditions, the microcomputer does not operate normally and may
perform unstable operation.
In a system where the power source voltage drops slowly when the
power source voltage drops or the power supply is turned off, reset
a microcomputer when the supply voltage is less than the recom-
mended operating conditions and design a system not to cause
errors to the system by this unstable operation.
Register initial values 1
The initial value of the following registers are undefined after sys-
tem is released from reset. After system is released from reset, set
initial values.
Register Z (2 bits)
Register D (3 bits)
Register E (8 bits)
Register initial values 2
The initial value of the following registers are undefined at RAM
back-up. After system is returned from RAM back-up, set initial val-
ues.
Register Z (2 bits)
Register X (4 bits)
Register Y (4 bits)
Register D (3 bits)
Register E (8 bits)
Program counter
Make sure that the PCH does not specify after the last page of the
built-in ROM.
Stack registers (SKS) and stack pointer (SP)
Stack registers (SKs) are eight identical registers, so that subrou-
tines can be nested up to 8 levels. However, one of stack registers
is used respectively when using an interrupt service routine and
when executing a table reference instruction. Accordingly, be care-
ful not to over the stack when performing these operations
together.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC705MC4CP | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP28 |
| MC9S12HZ64MFU | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37547G2FP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| M38D58G8-XXXHP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80 |
| MC6805R3S | 8-BIT, MROM, MICROCONTROLLER, CDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M34509G4H-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34509G4-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34509T2-CPE | 功能描述:DEV TOOL COMPACT EMULATOR: 4508/ RoHS:否 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:- 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:* |
| M34512M2 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34512M2-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。