参数资料
型号: M34509G4HFP
元件分类: 微控制器/微处理器
英文描述: 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO24
封装: 5.30 X 10.10 MM, 0.80 MM PITCH, PLASTIC, SSOP-24
文件页数: 108/143页
文件大小: 1056K
代理商: M34509G4HFP
4509 Group
Rev.1.03
2009.07.27
page 67 of 140
REJ03B0147-0103
NOTES ON NOISE
Countermeasures against noise are described below.
The following countermeasures are effective against noise in theory,
however, it is necessary not only to take measures as follows but to
evaluate before actual use.
1. Shortest wiring length
(1) Wiring for RESET pin
Make the length of wiring which is connected to the RESET pin as
short as possible. Especially, connect a capacitor across the
RESET pin and the VSS pin with the shortest possible wiring.
<Reason>
In order to reset a microcomputer correctly, 1 machine cycle or more
of the width of a pulse input into the RESET pin is required.
If noise having a shorter pulse width than this is input to the RESET
input pin, the reset is released before the internal state of the micro-
computer is completely initialized.
This may cause a program runaway.
Fig. 64 Wiring for the RESET pin
(2) Wiring for clock input/output pins
Make the length of wiring which is connected to clock I/O pins as
short as possible.
Make the length of wiring across the grounding lead of a capacitor
which is connected to an oscillator and the VSS pin of a microcom-
puter as short as possible.
Separate the VSS pattern only for oscillation from other VSS pat-
terns.
<Reason>
If noise enters clock I/O pins, clock waveforms may be deformed.
This may cause a program failure or program runaway. Also, if a po-
tential difference is caused by the noise between the VSS level of a
microcomputer and the VSS level of an oscillator, the correct clock
will not be input in the microcomputer.
RESET
Reset
circuit
Noise
VSS
Reset
circuit
VSS
RESET
VSS
N.G.
O.K.
Noise
XIN
XOUT
VSS
XIN
XOUT
VSS
N.G.
O.K.
(3) Wiring to CNVSS pin
Connect CNVSS pin to a GND pattern at the shortest distance.
The GND pattern is required to be as close as possible to the GND
supplied to VSS.
In order to improve the noise reduction, to connect a 5 k resistor
serially to the CNVSS pin - GND line may be valid.
As well as the above-mentioned, in this case, connect to a GND pat-
tern at the shortest distance. The GND pattern is required to be as
close as possible to the GND supplied to VSS.
<Reason>
The CNVSS pin of the QzROM is the power source input pin for the
built-in QzROM. When programming in the built-in QzROM, the im-
pedance of the CNVSS pin is low to allow the electric current for
writing flow into the QzROM. Because of this, noise can enter easily.
If noise enters the CNVSS pin, abnormal instruction codes or data
are read from the built-in QzROM, which may cause a program run-
away.
Fig. 66 Wiring for the CNVSS pin of the QzPROM
About 5k
VSS
The shortest
CNVSS
(Note)
Note: This indicates pin.
Fig. 65 Wiring for clock I/O pins
相关PDF资料
PDF描述
MC68HC705MC4CP 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP28
MC9S12HZ64MFU 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
M37547G2FP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36
M38D58G8-XXXHP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PQFP80
MC6805R3S 8-BIT, MROM, MICROCONTROLLER, CDIP40
相关代理商/技术参数
参数描述
M34509G4H-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34509G4-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34509T2-CPE 功能描述:DEV TOOL COMPACT EMULATOR: 4508/ RoHS:否 类别:编程器,开发系统 >> 内电路编程器、仿真器以及调试器 系列:- 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:*
M34512M2 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34512M2-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER