- 您现在的位置：买卖IC网 > PDF目录69012 > M37271EFSP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP52 PDF资料下载
参数资料
| 型号： | M37271EFSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP52 |
| 封装： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-52 |
| 文件页数： | 39/64页 |
| 文件大小： | 1252K |
| 代理商： | M37271EFSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
MITSUBISHI MICROCOMPUTERS
M37271MF-XXXSP
M37271EF-XXXSP, M37271EFSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
41
Table 7. Set values of I2C clock control register and SCL
frequency
(4) I2C Control Register
The I2C control register (address 00F916) controls data communica-
tion format.
s Bits 0 to 2: Bit counter (BC0–BC2)
These bits decide the number of bits for the next 1-byte data to be
transmitted. An interrupt request signal occurs immediately after the
number of bits specified with these bits are transmitted.
When a START condition is received, these bits become “0002” and
the address data is always transmitted and received in 8 bits.
s Bit 3: I2C interface use enable bit (ES0)
This bit enables to use the multimaster I2C BUS interface. When this
bit is set to “0,” the use disable status is provided, so the SDA and
the SCL become high-impedance. When the bit is set to “1,” use of
the interface is enabled.
When ES0 = “0,” the following is performed.
PIN = “1,” BB = “0” and AL = “0” are set (they are bits of the I2C
status register at address 00F816 ).
Writing data to the I2C data shift register (address 00F616) is dis-
abled.
s Bit 4: Data format selection bit (ALS)
This bit decides whether or not to recognize slave addresses. When
this bit is set to “0,” the addressing format is selected, so that ad-
dress data is recognized. When a match is found between a slave
address and address data as a result of comparison or when a gen-
eral call (refer to “(5) I2C Status Register,” bit 1) is received, trans-
mission processing can be performed. When this bit is set to “1,” the
free data format is selected, so that slave addresses are not recog-
nized.
s Bit 5: Addressing format selection bit (10BIT SAD)
This bit selects a slave address specification format. When this bit is
set to “0,” the 7-bit addressing format is selected. In this case, only
the high-order 7 bits (slave address) of the I2C address register (ad-
dress 00F716) are compared with address data. When this bit is set
to “1,” the 10-bit addressing format is selected, all the bits of the I2C
address register are compared with address data.
s Bits 6 and 7: Connection control bits between I2C-BUS interface
and ports (BSEL0, BSEL1)
These bits controls the connection between SCL and ports or SDA
and ports (refer to Figure 42).
Fig. 41. Structure of I2C clock control register
ACK
BIT
FAST
MODE
CCR4 CCR3 CCR2 CCR1 CCR0
I2C clock control register
(S2 : address 00FA16)
70
SCL frequency
control bits
Refer to Table 7.
SCL mode
specification bit
0 : Standard clock
mode
1 : High-speed clock
mode
ACK bit
0 : ACK is returned.
1 : ACK is not returned.
ACK clock bit
0 : No ACK clock
1 : ACK clock
SCL frequency
(at
φ = 4MHz, unit : kHz)
Setting value of
CCR4–CCR0
Standard clock
mode
Setting disabled
100
83.3
500/CCR value
17.2
16.6
16.1
High-speed clock
mode
Setting disabled
333
250
400(Note)
166
1000/CCR value
34.5
33.3
32.3
CCR4
0
1
CCR3
0
1
CCR2
0
1
CCR1
0
1
0
1
0
1
CCR0
0
1
0
1
0
1
0
1
0
1
Note: At 400 kHz in the high-speed clock mode, the duty is 40%.
In the other cases, the duty is 50%.
…
相关PDF资料 |
PDF描述 |
|---|---|
| M37271MF-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52 |
| M37272M6-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37273MF-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52 |
| M37274EFSP | 8-BIT, OTPROM, MICROCONTROLLER, PDIP52 |
| M37274EFSP | 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP52 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37271EFSS | 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 类别:编程器，开发系统 >> 配件 系列:- 标准包装:1 系列:- 附件类型:适配器板 适用于相关产品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37271EF-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-213SP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
| M37271MF-219SP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。