参数资料
型号: M37540M2T-XXXFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
封装: 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32
文件页数: 29/88页
文件大小: 872K
代理商: M37540M2T-XXXFP
7540 Group
Rev.4.00
Jun 21, 2004
page 35 of 82
REJ03B0011-0400Z
Fig. 32 Block diagram of UART serial I/O1
(2) Asynchronous Serial I/O (UART) Mode
Clock asynchronous serial I/O mode (UART) can be selected by
clearing the serial I/O1 mode selection bit of the serial I/O1 control
register to “0”.
Eight serial data transfer formats can be selected, and the transfer
formats used by a transmitter and receiver must be identical.
XIN
1/4
OE
PE FE
1/16
Data bus
Receive buffer register
Address 001816
Receive shift register
Receive buffer full flag (RBF)
Receive interrupt request (RI)
Baud rate generator
Frequency division ratio 1/(n+1)
Address 001C16
ST/SP/PA generator
Transmit buffer register
Data bus
Transmit shift register
Address 001816
Transmit shift completion flag (TSC)
Transmit buffer empty flag (TBE)
Transmit interrupt request (TI)
Address 001916
ST detector
SP detector
UART control register
Address 001B16
Character length selection bit
Address 001A16
BRG count source selection bit
Transmit interrupt source selection bit
Serial I/O1 synchronous clock selection bit
Clock control circuit
Character length selection bit
7 bits
8 bits
Serial I/O1 control register
P12/SCLK1
Serial I/O1 status register
P10/RXD1
P11/TXD1
The transmit and receive shift registers each have a buffer, but the
two buffers have the same address in memory. Since the shift reg-
ister cannot be written to or read from directly, transmit data is
written to the transmit buffer register, and receive data is read
from the receive buffer register.
The transmit buffer register can also hold the next data to be
transmitted, and the receive buffer register can hold a character
while the next character is being received.
Fig. 33 Operation of UART serial I/O1 function
TSC=0
TBE=1
RBF=0
TBE=0
RBF=1
ST
D0
D1
SP
D0
D1
ST
SP
TBE=1
TSC=1
ST
D0
D1
SP
D0
D1
ST
SP
Transmit or receive clock
Transmit buffer write
signal
Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).
2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit
interrupt source selection bit (TIC) of the serial I/O1 control register.
3: The receive interrupt (RI) is set when the RBF flag becomes “1.”
4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Notes
Serial output TXD
Serial input RXD
Receive buffer read
signal
相关PDF资料
PDF描述
M37540M2V-XXXFP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
M37540M4V-XXXGP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO36
M30624MGP-XXXGP 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
M37478E8SP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42
MC68HC908GR8AMDW 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PDSO28
相关代理商/技术参数
参数描述
M37540M2T-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M2V-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540M2V-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M2-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M2-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER