参数资料
型号: M37540M2T-XXXFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
封装: 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32
文件页数: 36/88页
文件大小: 872K
代理商: M37540M2T-XXXFP
7540 Group
Rev.4.00
Jun 21, 2004
page 41 of 82
REJ03B0011-0400Z
Watchdog Timer
The watchdog timer gives a means for returning to a reset status
when the program fails to run on its normal loop due to a runaway.
The watchdog timer consists of an 8-bit watchdog timer H and an
8-bit watchdog timer L, being a 16-bit counter.
Standard operation of watchdog timer
The watchdog timer stops when the watchdog timer control regis-
ter (address 003916) is not set after reset. Writing an optional
value to the watchdog timer control register (address 003916)
causes the watchdog timer to start to count down. When the
watchdog timer H underflows, an internal reset occurs. Accord-
ingly, it is programmed that the watchdog timer control register
(address 003916) can be set before an underflow occurs.
When the watchdog timer control register (address 003916) is
read, the values of the high-order 6-bit of the watchdog timer H,
STP instruction disable bit and watchdog timer H count source se-
lection bit are read.
Initial value of watchdog timer
By a reset or writing to the watchdog timer control register (ad-
dress 003916), the watchdog timer H is set to “FF16” and the
watchdog timer L is set to “FF16”.
Operation of watchdog timer H count source selection bit
A watchdog timer H count source can be selected by bit 7 of the
watchdog timer control register (address 003916). When this bit is
“0”, the count source becomes a watchdog timer L underflow sig-
nal. The detection time is 131.072 ms at f(XIN)=8 MHz.
When this bit is “1”, the count source becomes f(XIN)/16. In this
case, the detection time is 512
s at f(XIN)=8 MHz.
This bit is cleared to “0” after reset.
Operation of STP instruction disable bit
When the watchdog timer is in operation, the STP instruction can
be disabled by bit 6 of the watchdog timer control register (ad-
dress 003916).
When this bit is “0”, the STP instruction is enabled.
When this bit is “1”, the STP instruction is disabled, and an inter-
nal reset occurs if the STP instruction is executed.
Once this bit is set to “1”, it cannot be changed to “0” by program.
This bit is cleared to “0” after reset.
Fig. 41 Block diagram of watchdog timer
Fig. 42 Structure of watchdog timer control register
XIN
Data bus
“0”
“1”
1/16
Watchdog timer H count
source selection bit
Reset
circuit
STP Instruction disable bit
Watchdog timer H (8)
Write "FF16" to the
watchdog timer
control register
Internal reset
RESET
Watchdog timer L (8)
STP Instruction
Write “FF16” to the
watchdog timer
control register
Watchdog timer control register
(WDTCON: address 003916, initial value: 3F16)
Watchdog timer H (read only for high-order 6-bit)
STP instruction disable bit
0 : STP instruction enabled
1 : STP instruction disabled
Watchdog timer H count source selection bit
0 : Watchdog timer L underflow
1 : f(XIN)/16
b7
b0
相关PDF资料
PDF描述
M37540M2V-XXXFP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
M37540M4V-XXXGP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO36
M30624MGP-XXXGP 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
M37478E8SP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42
MC68HC908GR8AMDW 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PDSO28
相关代理商/技术参数
参数描述
M37540M2T-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M2V-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37540M2V-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M2-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES
M37540M2-XXXGP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER