- 您现在的位置：买卖IC网 > PDF目录69014 > M37733MHBXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37733MHBXXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 14/89页 |
| 文件大小： | 1506K |
| 代理商： | M37733MHBXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
21
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
Fig. 21 Timer Aj mode register bit configuration when performing
two-phase pulse signal processing in event counter mode
Fig. 20 Two-phase pulse signal processing operation of timer A4
Fig. 19 Two-phase pulse signal processing operation of timer A2
Furthermore, in the event counter mode, whether to increment or
decrement the counter can also be determined by supplying two kinds
of pulses of which phases differ by 90° to timer A2, A3, or A4. There
are two types of two-phase pulse signal processing operations. One
uses timer A2 and the other uses timer A4. Timer A3 can select one
of these two operations with bit 7 of the timer A3 mode register. In
both processing operations, two kinds of pulses of which phases differ
by 90° are input to the TAjOUT (j = 2 to 4) pin and TAjIN pin respectively.
After the level of the TA2OUT pin changes from “L” to “H” with timer
A2 used, as shown in Figure 19, the count is incremented when a
rising edge is input to the TA2IN pin and the count is decremented
when the falling edge is input.
For timer A4, as shown in Figure 20, when a phase related pulse
with a rising edge input to the TA4IN pin is input after the level of
TA4OUT pin changes from “L” to “H”, the count is incremented at the
respective rising edge and falling edge of the TA4OUT pin and TA4IN
pin. When a phase related pulse with a falling edge input to the TA4OUT
pin is input after the level of TA4IN pin changes from “H” to “L”, the
count is decremented at the respective rising edge and falling edge
of the TA4IN pin and TA4OUT pin.
When performing this two-phase pulse signal processing, bits 0 and
4 of the timer Aj mode register must be set to “1” and bits 1, 2, 3, and
5 must be set to “0” as shown in Figure 21.
Bit 7 is used to select whether to perform two-phase pulse signal
processing for timer A3 in the same manner as timer A2 or as timer
A4. When this bit is “0”, two-phase pulse signal processing for timer
A3 is performed in the same manner as timer A2 and when it is “1”, it
is performed in the same manner as timer A4. This bit is ignored for
timers A2 and A4.
Note that bits 5, 6, and 7 of the up-down flag (address 4416) are the
two-phase pulse signal processing selection bits for timers A2, A3,
and A4, respectively.
Each timer operates in the normal event counter mode when the
corresponding bit is “0” and performs two-phase pulse signal
processing when it is “1”.
Count is started by setting the count start flag to “1”. Data write and
read are performed in the same way as for the normal event counter
mode. Note that the port direction register of the input port must be
set to the input mode because two-phase pulse signal is input. Also,
there can be no pulse output in this mode.
TA2OUT
TA2IN
Increment
count
Increment
count
Increment
count
Decrement
count
Decrement
count
Decrement
count
TA4OUT
TA4IN
Increment count at each edge
Decrement count at each edge
Increment count at each edge
Decrement count at each edge
Addresses
0 1 : Always “01” in event counter
mode
7 65 43 2 1 0
00 1
0 1 0 0 : Always “0100” when processing
two-phase pulse signal
Timer A2 mode register
5816
Timer A3 mode register
5916
Timer A4 mode register
5A16
100
0 : Reload
1 : No reload
This bit is avilable for timer A3
0 : Two-phase pulse signal processing
in the same manner as timer A2
1 : Two-phase pulse signal processing
in the same manner as timer A4
相关PDF资料 |
PDF描述 |
|---|---|
| M37734E8BFS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC80 |
| M37734E8BXXXFP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37735EHBFS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC80 |
| M37735EHBXXXFP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37735EHLXXXHP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37733MHL | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHLXXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733S4 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37733S4BFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37733S4LHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。