- 您现在的位置：买卖IC网 > PDF目录69014 > M37733MHBXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37733MHBXXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 17/89页 |
| 文件大小： | 1506K |
| 代理商： | M37733MHBXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
24
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
(4) Pulse width modulation mode [11]
Figure 26 shows the bit configuration of the timer Ai mode register
during the pulse width modulation mode. In the pulse width modulation
mode, bits 0, 1, and 2 must be set to “1”.
Bit 5 is used to determine whether to perform as the 16-bit length
pulse width modulator or the 8-bit length pulse width modulator. 16-
bit length pulse width modulator is selected when bit 5 is “0” and 8-bit
length pulse width modulator is selected when bit 5 is “1”. The 16-bit
length pulse width modulator is described first.
The pulse width modulator can be started with a software trigger or
with an input signal from a TAiIN pin (external trigger).
The software trigger mode is selected when bit 4 is “0”. Pulse width
modulator is started and pulse is output from the TAiOUT pin when
the timer Ai start flag is set to “1”.
The external trigger mode is selected when bit 4 is “1”. Pulse width
modulator starts when a trigger signal is input from the TAiIN pin when
the timer Ai start flag is “1”. Whether to trigger at the fall or rise of the
trigger signal is determined by bit 3. The trigger is at the fall of the
trigger signal when bit 3 is “0” and at the rise when it is “1”.
When data is written to timer Ai with the pulse width modulator halted,
it is written to the reload register and the counter.
Then when the timer Ai start flag is set to “1” and a software trigger or
an external trigger is issued to start modulation, the waveform shown
in Figure 27 is output continuously. Once modulation is started,
triggers are not accepted. If the value in the reload register is m, the
duration “H” of pulse is
The reload register and the counter are both divided into 8-bit halves.
The low-order 8 bits function as a prescaler and the high-order 8 bits
function as the 8-bit length pulse width modulator. The prescaler
counts the clock selected by bits 6 and 7. A pulse is generated when
the counter reaches 000016 as shown in Figure 28. At the same time,
the contents of the reload register is transferred to the counter, and
count is continued.
Fig. 26 Timer Ai mode register bit configuration during pulse width
modulation mode
An interrupt request signal is generated and the interrupt request bit
of the timer Ai interrupt control register is set at each fall of the output
pulse.
The width of the output pulse is changed by updating timer data. The
update can be performed at any time. The output pulse width is
changed at the rise of the pulse after data is written to the timer.
The contents of the reload register is transferred to the counter just
before the rise of the next output pulse so that the pulse width is
changed from the next output pulse.
Undefined data is read when timer Ai is read.
The 8-bit length pulse width modulator is described next.
The 8-bit length pulse width modulator is selected when bit 5 of the
timer Ai mode register is “1”.
1
selected clock frequency
! m
and the output pulse period is
1
selected clock frequency
! (216 – 1).
76 54 3 2 1 0
11
1
Timer A0 mode register
5616
Timer A1 mode register
5716
Timer A2 mode register
5816
Timer A3 mode register
5916
Timer A4 mode register
5A16
Addresses
1 : Always “1” in pulse width
modulation mode
0 ! : Software trigger
1 0 : Trigger at the falling of TAiIN input
1 1 : Trigger at the rising of TAiIN input
Clock source selection bit
0 0 : Select f2
0 1 : Select f16
1 0 : Select f64
1 1 : Select f512
1 1 : Always “11” in pulse width
modulation mode
0 : 16 bit pulse width modulator
1 : 8 bit pulse width modulator
相关PDF资料 |
PDF描述 |
|---|---|
| M37734E8BFS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC80 |
| M37734E8BXXXFP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37735EHBFS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC80 |
| M37735EHBXXXFP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37735EHLXXXHP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37733MHL | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHLXXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733S4 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37733S4BFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37733S4LHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。