- 您现在的位置：买卖IC网 > PDF目录69014 > M37733MHBXXXFP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37733MHBXXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 15/89页 |
| 文件大小： | 1506K |
| 代理商： | M37733MHBXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
22
MITSUBISHI MICROCOMPUTERS
M37733MHBXXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
(3) One-shot pulse mode [10]
Figure 22 shows the bit configuration of the timer Ai mode resister
during the one-shot pulse mode. In the one-shot pulse mode, bit 0
and bit 5 must be “0” and bit 1 and bit 2 must be “1”.
The trigger is enabled when the count start flag is “1”. The trigger
can be generated by software, or it can be input from the TAiIN pin.
Software trigger is selected when bit 4 is “0”, and the input signal
from the TAiIN pin is used as the trigger when bit 4 is “1”.
Bit 3 is used to determine whether to trigger at the fall of the trigger
signal or at the rise. The trigger is at the fall of the trigger signal when
bit 3 is “0” and at the rise of the trigger signal when bit 3 is “1”.
Software trigger is generated by setting the bit of the one-shot start
flag corresponding to each timer.
Figure 23 shows the bit configuration of the one-shot start flag.
As shown in Figure 24, when a trigger signal is received, the counter
counts the clock selected by bits 6 and 7.
If the contents of the counter is not 000016, the TAiOUT pin goes “H”
when a trigger signal is received. The count direction is decrement.
When the counter reaches 000116, the TAiOUT pin goes “L” and count
is stopped. The contents of the reload register is transferred to the
counter. At the same time, an interrupt request signal is generated,
and the interrupt request bit of the timer Ai interrupt control register is
set. This is repeated each time a trigger signal is received. The output
pulse width is
1
pulse frequency of the selected clock
! (counter’s value at the time of trigger).
If the count start flag is “0”, the level of the TAiOUT pin goes “L”.
Therefore, the counter’s value corresponding to the desired pulse
width must be written to timer Ai before setting “1” to the timer Ai
count start flag.
As shown in Figure 25, a trigger signal can be received before the
operation for the previous trigger signal is completed. In this case,
the contents of the reload register is transferred to the counter by the
trigger, and then that value is decremented.
Except when retriggering while operating, the contents of the reload
register is not transferred to the counter by triggering.
When retriggering, there must be at least two timer count source
cycles before a new trigger can be issued.
Fig. 22 Timer Ai mode register bit configuration during one-shot
pulse mode
Timer A0 mode register
5616
Timer A1 mode register
5716
Timer A2 mode register
5816
Timer A3 mode register
5916
Timer A4 mode register
5A16
Addresses
1 : Always “1” in one-shot pulse
mode
0 ! : Software trigger
1 0 : Trigger at the falling edge of
TAiIN input
1 1 : Trigger at the rising edge of
TAiIN input
0 : Always “0” in one-shot pulse
mode
Clock source selection
0 0 : Select f2
0 1 : Select f16
1 0 : Select f64
1 1 : Select f512
1 0 : Always “10” in one-shot
pulse mode
7 65 43 2 1 0
01 0
1
相关PDF资料 |
PDF描述 |
|---|---|
| M37734E8BFS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC80 |
| M37734E8BXXXFP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37735EHBFS | 16-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC80 |
| M37735EHBXXXFP | 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| M37735EHLXXXHP | 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37733MHL | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733MHLXXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37733S4 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37733S4BFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37733S4LHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。