- 您现在的位置：买卖IC网 > PDF目录98007 > M37906F8CSP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 PDF资料下载
参数资料
| 型号： | M37906F8CSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| 封装： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件页数： | 16/37页 |
| 文件大小： | 352K |
| 代理商： | M37906F8CSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
M37906F8CFP, M37906F8CSP
16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
20
Table 2. Software commands (CPU reprogramming mode)
Command
Read Array
Read Status Register
Clear Status Register
Programming
Block Erase
Erase All Block
Address
X (Note 2)
X
FF16
7016
5016
4016
2016
1st cycle
2nd cycle
Notes 1: At software commands’ input, the high-order byte of data (D8–D15) is ignored.
2: X = An arbitrary address in the user ROM area. (Note that A0 = “0”.)
3: SRD = Status Register Data
4: WA = Write Address, WD = Write Data (16 bits).
5: Block address: the maximum address of each block must be input. Note that address A0 = “0”.
Mode
Write
(D0 to D7)
Data
Address
—
X
—
WA (Note 4)
BA (Note 5)
X
—
SRD (Note 3)
—
WD (Note 4)
D016
2016
Mode
—
Read
—
Write
Block Erase Command (2016/D016)
Writing command code “2016” at the 1st bus cycle and writing confir-
mation command code “D016” and the maximum address of the
block (Note that address A0 = “0”.) at the subsequent 2nd bus cycle
initiate the automatic erase (erasing and erase verification) operation
for the specified block.
The completion of the automatic erase operation is confirmed by a
read of the flash memory control register. The RY/BY status bit of the
flash memory control register goes “0” simultaneously with start of
the automatic erase operation; and also, it goes “1” simultaneously
with completion of it.
Before execution of the next command, be sure to confirm that the
RY/BY status bit is set to “1” (READY). During the automatic erase
operation, writing of commands and access to the flash memory
must not be performed.
Simultaneously with start of the automatic erase, the read status reg-
ister mode is automatically active. In this case, the read status regis-
ter mode is retained until the next read array command (FF16) is
written or until the reset is performed by using the flash memory re-
set bit.
Reading out the status register after the automatic erase operation
is completed reports the result of it. For details, refer to the section
on the status register.
Figure 10 shows an example of the block erase flowchart.
Data
相关PDF资料 |
PDF描述 |
|---|---|
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38184E8-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
| M38184EA-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
| M38184EAFP | 8-BIT, OTPROM, 8.4 MHz, MICROCONTROLLER, PQFP100 |
| M38222M2DXXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37906M4C-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4C-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4H-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M6C-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M6C-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。