- 您现在的位置：买卖IC网 > PDF目录98007 > M37906F8CSP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 PDF资料下载
参数资料
| 型号： | M37906F8CSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| 封装： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件页数： | 19/37页 |
| 文件大小： | 352K |
| 代理商： | M37906F8CSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
16-BIT CMOS MICROCOMPUTER
M37906F8CFP, M37906F8CSP
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
23
Fig. 11 Full status check flowchart and actions to be taken if an error has ocurred
AC Electrical Characteristics (VCC = 5 V ± 0.5 V, Ta = 0 to 60 °C, f(fsys) = 20 MHz (Note))
Symbol
Parameter
Limits
Unit
Min.
Typ.
Max.
VCC power source current (at read)
VCC power source current (at write)
VCC power source current (at programming)
VCC power source current (at erasing)
48
54
DC Electrical Characteristics (VCC = 5 V ± 0.5 V, Ta = 0 to 60 °C, f(fsys) = 20 MHz (Note))
Limits of VIH, VIL, VOH, VOL, IIH, and IIL for each pin are the same as those in the microcomputer mode.
Note: f(fsys) indicates the system clcok (fsys) frequency.
mA
Parameter
256-byte programming time
Block erase time
Erase all block time
Limits
Unit
Min.
Typ.
Max.
4
0.6
0.6 n
40
8
8 n
ms
s
n = Number of blocks to be erased
Icc1
Icc2
Icc3
Icc4
30
The limits of parameters other than the above are same as those in the microcomputer mode.
Note: f(fsys) indicates the system clock (fsys) frequency.
Status Register Read
SR.4 = 1
NO
Command Sequence
Error
YES
SR.5 = 0?
YES
Block Erase Error
NO
SR.4 = 0?
YES
Programming Error
NO
End
(Block erase, Programming)
and
SR.5 = 1
?
Execute the clear status register command (5016) to clear the status register.
Confirm whether the command has correctly been input or not; and then,
start the operation again.
Perform the block erase operation again.
If an error occurs even after the above operation is performed, the block cannot be used.
Perform the programming operation again.
If an error occurs even after the above operation is performed, the word cannot be used.
Note: Under the condition that any of SR.5 and SR.4 = “1”, none of the programming,
block erase, and erase all block commands can be accepted. Before execution
of these commands, execute the clear status register command (5016) in advance.
相关PDF资料 |
PDF描述 |
|---|---|
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38184E8-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
| M38184EA-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
| M38184EAFP | 8-BIT, OTPROM, 8.4 MHz, MICROCONTROLLER, PQFP100 |
| M38222M2DXXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37906M4C-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4C-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4H-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M6C-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M6C-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。