- 您现在的位置：买卖IC网 > PDF目录80563 > M38037M6H-XXXSP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PDIP64 PDF资料下载
参数资料
| 型号： | M38037M6H-XXXSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PDIP64 |
| 封装： | 0.750 INCH, 1.78 MM PITCH, SHRINK, PLASTIC, DIP-64 |
| 文件页数： | 90/119页 |
| 文件大小： | 1818K |
| 代理商： | M38037M6H-XXXSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页当前第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页
Rev.3.11
Apr 5, 2006
Page 70 of 113
REJ03B0017-0311
3803 Group (Spec.H)
Outline Performance
CPU rewrite mode is usable in the single-chip or Boot mode. The
only User ROM area can be rewritten.
In CPU rewrite mode, the CPU erases, programs and reads the
internal flash memory as instructed by software commands. This
rewrite control program must be transferred to internal RAM
area before it can be executed.
The MCU enters CPU rewrite mode by setting “1” to the CPU
rewrite mode select bit (bit 1 of address 0FE016). Then, software
commands can be accepted.
Use software commands to control program and erase
operations. Whether a program or erase operation has terminated
normally or in error can be verified by reading the status register.
Figure.65 shows the flash memory control register 0.
Bit 0 of the flash memory control register 0 is the RY/BY status
flag used exclusively to read the operating status of the flash
memory. During programming and erase operations, it is “0”
(busy). Otherwise, it is “1” (ready).
Bit 1 of the flash memory control register 0 is the CPU rewrite
mode select bit. When this bit is set to “1”, the MCU enters CPU
rewrite mode. And then, software commands can be accepted. In
CPU rewrite mode, the CPU becomes unable to access the
internal flash memory directly. Therefore, use the control
program in the internal RAM for write to bit 1. To set this bit 1 to
“1”, it is necessary to write “0” and then write “1” in succession
to bit 1. The bit can be set to “0” by only writing “0”.
Bit 2 of the flash memory control register 0 is the 8 KB user
block E/W enable bit. By setting combination of bit 4 of the flash
memory control register 2 and this bit as shown in Table 12, E/W
is disabled to user block in the CPU rewriting mode.
Bit 3 of the flash memory control register 0 is the flash memory
reset bit used to reset the control circuit of internal flash memory.
This bit is used when flash memory access has failed. When the
CPU rewrite mode select bit is “1”, setting “1” for this bit resets
the control circuit. To release the reset, it is necessary to set this
bit to “0”.
Bit 5 of the flash memory control register 0 is the User ROM
area select bit and is valid only in the boot mode. Setting this bit
to “1” in the boot mode switches an accessible area from the boot
ROM area to the user ROM area. To use the CPU rewrite mode
in the boot mode, set this bit to “1”. To rewrite bit 5, execute the
useroriginal reprogramming control software transferred to the
internal RAM in advance.
Bit 6 of the flash memory control register 0 is the program status
flag. This bit is set to “1” when writing to flash memory is failed.
When program error occurs, the block cannot be used.
Bit 7 of the flash memory control register 0 is the erase status
flag.
This bit is set to “1” when erasing flash memory is failed. When
erase error occurs, the block cannot be used.
Figure.66 shows the flash memory control register 1.
Bit 0 of the flash memory control register 1 is the Erase suspend
enable bit. By setting this bit to “1”, the erase suspend mode to
suspend erase processing temporaly when block erase command
is executed can be used. In order to set this bit to “1”, writing “0”
and “1” in succession to bit 0. In order to set this bit to “0”, write
“0” only to bit 0.
Bit 1 of the flash memory control register 1 is the erase suspend
request bit. By setting this bit to “1” when erase suspend enable
bit is “1”, the erase processing is suspended.
Bit 6 of the flash memory control register 1 is the erase suspend
flag. This bit is cleared to “0” at the flash erasing.
Fig 65. Structure of flash memory control register 0
Fig 66. Structure of flash memory control register 1
Flash memory control register 0
(FMCR0: address : 0FE016: initial value: 0116)
RY/BY status flag
0 : Busy (being written or erased)
1 : Ready
CPU rewrite mode select bit(1)
0 : CPU rewrite mode invalid
1 : CPU rewrite mode valid
8KB user block E/W enable bit(1, 2)
0 : E/W disabled
1 : E/W enabled
Flash memory reset bit(3, 4)
0 : Normal operation
1 : reset
Not used (do not write “1” to this bit.)
User ROM area select bit(5)
0 : Boot ROM area is accessed
1 : User ROM area is accessed
Program status flag
0: Pass
1: Error
Erase status flag
0: Pass
1: Error
b7
b0
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to this
bit.
2: This bit can be written only when CPU rewrite mode select bit is “1”.
3: Effective only when the CPU rewrite mode select bit = “1”. Fix this
bit to “0” when the CPU rewrite mode select bit is “0”.
4: When setting this bit to “1” (when the control circuit of flash memory
is reset), the flash memory cannot be accessed for 10
s.
5: Write to this bit in program on RAM
Flash memory control register 1
(FMCR1: address : 0FE116: initial value: 4016)
Erase Suspend enble bit(1)
0 : Suspend invalid
1 : Suspend valid
Erase Suspend request bit(2)
0 : Erase restart
1 : Suspend request
Not used (do not write “1” to this bit.)
Erase Suspend flag
0 : Erase active
1 : Erase inactive (Erase Suspend mode)
Not used (do not write “1” to this bit.)
b7
b0
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to this
bit.
2: Effective only when the suspend enable bit = “1”.
相关PDF资料 |
PDF描述 |
|---|---|
| M38513E4FP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M37225M8-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M37272EFFP | 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
| M37512FCH-XXXHP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 |
| M38073E4FS | 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38037M8108F | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38037M8H-194HP#U0 | 制造商:Renesas Electronics Corporation 功能描述:8BIT CISC - Trays |
| M38039FFHFP#U0 | 功能描述:IC 740 MCU FLASH 60K 64QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38039FFHHP | 功能描述:MCU 3/5V 56K+4K 64-LQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| M38039FFH-HP#U | 制造商:Renesas Electronics Corporation 功能描述:8BIT 740 CISC 56KB FLASH 16.8MHZ 3.3/5V - Trays |
发布紧急采购，3分钟左右您将得到回复。