- 您现在的位置：买卖IC网 > PDF目录80563 > M38037M6H-XXXSP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PDIP64 PDF资料下载
参数资料
| 型号： | M38037M6H-XXXSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PDIP64 |
| 封装： | 0.750 INCH, 1.78 MM PITCH, SHRINK, PLASTIC, DIP-64 |
| 文件页数： | 93/119页 |
| 文件大小： | 1818K |
| 代理商： | M38037M6H-XXXSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页当前第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页
Rev.3.11
Apr 5, 2006
Page 73 of 113
REJ03B0017-0311
3803 Group (Spec.H)
Software Commands
Table 13 lists the software commands.
After setting the CPU rewrite mode select bit to “1”, execute a
software command to specify an erase or program operation.
Each software command is explained below.
Read Array Command (FF16)
The read array mode is entered by writing the command code
“FF16” in the first bus cycle. When an address to be read is input
in one of the bus cycles that follow, the contents of the specified
address are read out at the data bus (D0 to D7).
The read array mode is retained until another command is
written.
Read Status Register Command (7016)
When the command code “7016” is written in the first bus cycle,
the contents of the status register are read out at the data bus (D0
to D7) by a read in the second bus cycle.
The status register is explained in the next section.
Clear Status Register Command (5016)
This command is used to clear the bits SR4 and SR5 of the status
register after they have been set. These bits indicate that
operation has ended in an error. To use this command, write the
command code “5016” in the first bus cycle.
Program Command (4016)
Program operation starts when the command code “4016” is
written in the first bus cycle. Then, if the address and data to
program are written in the 2nd bus cycle, program operation
(data programming and verification) will start.
Whether the write operation is completed can be confirmed by
read status register or the RY/BY status flag. When the program
starts, the read status register mode is entered automatically and
the contents of the status register is read at the data bus (D0 to
D7). The status register bit 7 (SR7) is set to “0” at the same time
the write operation starts and is returned to “1” upon completion
of the write operation. In this case, the read status register mode
remains active until the read array command (FF16) is written.
The RY/BY status flag of the flash memory control register is
“0” during write operation and “1” when the write operation is
completed as is the status register bit 7.
At program end, program results can be checked by reading the
status register.
Fig 69. Program flowchart
NOTES:
1. SRD = Status Register Data
2. WA = Write Address, WD = Write Data
3. BA = Block Address to be erased (Input the maximum address of each block.)
4. X denotes a given address in the User ROM area.
Start
Write “4016”
SR7 =
“1”?
or
RY/BY =
“1”?
Read status register
Program completed
NO
YES
Write
Write address
Write data
SR4 = “0”?
Program error
NO
YES
Table 13
List of software commands (CPU rewrite mode)
Command
cycle
number
First bus cycle
Second bus cycle
Mode
Address
Data
(D0 to D7)
Mode
Address
Data
(D0 to D7)
Read array
1
Write
X(4)
FF16
Read status register
2
Write
X
7016
Read
X
SRD(1)
Clear status register
1
Write
X
5016
Program
2
Write
X
4016
Write
WA(2)
WD(2)
Block erase
2
Write
X
2016
Write
BA(3)
D016
相关PDF资料 |
PDF描述 |
|---|---|
| M38513E4FP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO42 |
| M37225M8-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M37272EFFP | 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDSO42 |
| M37512FCH-XXXHP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP48 |
| M38073E4FS | 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38037M8108F | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38037M8H-194HP#U0 | 制造商:Renesas Electronics Corporation 功能描述:8BIT CISC - Trays |
| M38039FFHFP#U0 | 功能描述:IC 740 MCU FLASH 60K 64QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38039FFHHP | 功能描述:MCU 3/5V 56K+4K 64-LQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| M38039FFH-HP#U | 制造商:Renesas Electronics Corporation 功能描述:8BIT 740 CISC 56KB FLASH 16.8MHZ 3.3/5V - Trays |
发布紧急采购，3分钟左右您将得到回复。