- 您现在的位置：买卖IC网 > PDF目录80462 > M38507F8AFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PDSO42 PDF资料下载
参数资料
| 型号： | M38507F8AFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PDSO42 |
| 封装： | 8.40 X 17.50 MM, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件页数： | 15/59页 |
| 文件大小： | 885K |
| 代理商： | M38507F8AFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
Rev.2.13
Apr 17, 2009
Page 22 of 56
REJ03B0125-0213
3850 Group (Spec.A QzROM version)
TIMERS
The 3850 group (spec.A) has four timers: timer X, timer Y, timer
1, and timer 2.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are count down. When the timer reaches “0016”, an
underflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
Fig 17. Structure of timer XY mode register
Fig 18. Structure of timer count source selection register
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency
which is selected by timer 12 count source selection bit. The
output of prescaler 12 is counted by timer 1 and timer 2, and a
timer underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating
modes by setting the timer XY mode register.
(1) Timer Mode
The timer counts the count source selected by Timer count
source selection bit.
(2) Pulse Output Mode
The timer counts the count source selected by Timer count
source selection bit. Whenever the contents of the timer reach
“0016”, the signal output from the CNTR0 (or CNTR1) pin is
inverted. If the CNTR0 (or CNTR1) active edge selection bit is
“0”, output begins at “H”.
If it is “1”, output starts at “L”. When using a timer in this mode,
set the corresponding port P27 (or port P40) direction register to
output mode.
(3) Event Counter Mode
Operation in event counter mode is the same as in timer mode,
except that the timer counts signals input through the CNTR0 or
CNTR1 pin.
When the CNTR0 (or CNTR1) active edge selection bit is “0”,
the rising edge of the CNTR0 (or CNTR1) pin is counted.
When the CNTR0 (or CNTR1) active edge selection bit is “1”,
the falling edge of the CNTR0 (or CNTR1) pin is counted.
(4) Pulse Width Measurement Mode
If the CNTR0 (or CNTR1) active edge selection bit is “0”, the
timer counts the selected signals by the count source selection bit
while the CNTR0 (or CNTR1) pin is at “H”. If the CNTR0 (or
CNTR1) active edge selection bit is “1”, the timer counts it while
the CNTR0 (or CNTR1) pin is at “L”.
The count can be stopped by setting “1” to the timer X (or timer
Y) count stop bit in any mode. The corresponding interrupt
request bit is set each time a timer underflows.
<Notes>
When switching the count source by the timer 12, X and Y count
source bits, the value of timer count is altered in unconsiderable
amount owing to generating of a thin pulses in the count input
signals.
Therefore, select the timer count source before set the value to
the prescaler and the timer.
When timer X/timer Y underflow while executing the instruction
which sets “1” to the timer X/timer Y count stop bits, the timer
X/ timer Y interrupt request bits are set to “1”. Timer X/Timer Y
interrupts are received if these interrupts are enabled at this time.
The timing which interrupt is accepted has a case after the
instruction which sets “1” to the count stop bit, and a case after
the next instruction according to the timing of the timer
underflow. When this interrupt is unnecessary, set “0” (disabled)
to the interrupt enable bit and then set “1” to the count stop bit.
b7
Timer XY mode register
(TM : address 002316)
Timer X operating mode bit
b1 b0
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR0 active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer X count stop bit
0: Count start
1: Count stop
Timer Y operating mode bits
b5 b4
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR1 active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer Y count stop bit
0: Count start
1: Count stop
b0
Timer count source selection register
(TCSS : address 002816)
Timer X count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode)
1 : f(XIN)/2 (f(XCIN)/2 at low-speed mode)
Timer Y count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode)
1 : f(XIN)/2 (f(XCIN)/2 at low-speed mode)
Timer 12 count source selection bit
0 : f(XIN)/16 (f(XCIN)/16 at low-speed mode)
1 : f(XCIN)
Not used (returns “0” when read)
b7
b0
相关PDF资料 |
PDF描述 |
|---|---|
| MC68EN360RC33 | RISC MICROCONTROLLER, CPGA241 |
| MC56F8365MFG60 | 4-BIT, 120 MHz, OTHER DSP, PQFP128 |
| MPC8378ECVRANDA | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA689 |
| MB95F214KPH-G-SNE2 | 8-BIT, FLASH, MICROCONTROLLER, PDIP8 |
| MC9S12XS128J1VALR | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP112 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38507F8AFP#U1 | 功能描述:IC 740/3850 MCU FLASH 42SSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38507F8AFP#W1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 32K PB-FREE 42-SSOP T&R - Tape and Reel |
| M38507F8FP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 740 CISC 32KB Flash 5V 42-Pin SSOP 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#U1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#W1 | 制造商:Renesas Electronics Corporation 功能描述:FLASH 8-BIT 2.7 TO 5.5V PBFREE |
发布紧急采购，3分钟左右您将得到回复。