- 您现在的位置：买卖IC网 > PDF目录80462 > M38507F8AFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PDSO42 PDF资料下载
参数资料
| 型号： | M38507F8AFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PDSO42 |
| 封装： | 8.40 X 17.50 MM, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件页数： | 50/59页 |
| 文件大小： | 885K |
| 代理商： | M38507F8AFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
Rev.2.13
Apr 17, 2009
Page 54 of 56
REJ03B0125-0213
3850 Group (Spec.A QzROM version)
2. Notes when selecting clock asynchronous serial I/O
(Serial I/O1)
(1) Stop of transmission operation
Clear the transmit enable bit to “0” (transmit disabled).
<Reason>
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O1 enable bit is cleared to
“0” (Serial I/O1 disabled), the internal transmission is running
(in this case, since pins TxD, RxD, SCLK1, and SRDY1 function as
I/O ports, the transmission data is not output). When data is
written to the transmit buffer register in this state, data starts to
be shifted to the transmit shift register. When the serial I/O1
enable bit is set to “1” at this time, the data during internally
shifting is output to the TxD pin and an operation failure occurs.
(2) Stop of receive operation
Clear the receive enable bit to “0” (receive disabled).
(3) Stop of transmit/receive operation
Only transmission operation is stopped.
Clear the transmit enable bit to “0” (transmit disabled).
<Reason>
Since transmission is not stopped and the transmission circuit is
not initialized even if only the serial I/O1 enable bit is cleared to
“0” (Serial I/O1 disabled), the internal transmission is running
(in this case, since pins TxD, RxD, SCLK1, and SRDY1 function as
I/O ports, the transmission data is not output). When data is
written to the transmit buffer register in this state, data starts to
be shifted to the transmit shift register. When the serial I/O1
enable bit is set to “1” at this time, the data during internally
shifting is output to the TxD pin and an operation failure occurs.
Only receive operation is stopped.
Clear the receive enable bit to “0” (receive disabled).
3. Setting serial I/O1 control register again (Serial I/O1)
Set the serial I/O1 control register again after the transmission
and the reception circuits are reset by clearing both the transmit
enable bit and the receive enable bit to “0”.
Fig 54. Sequence of setting serial I/O1 control register
again
4. Data transmission control with referring to transmit
shift register completion flag (Serial I/O1)
The transmit shift register completion flag changes from “1” to
“0” with a delay of 0.5 to 1.5 shift clocks. When data
transmission is controlled with referring to the flag after writing
the data to the transmit buffer register, note the delay.
5. Transmit interrupt request when transmit enable bit
is set (Serial I/O1)
When the transmit interrupt is used, set the transmit interrupt
enable bit to transmit enabled as shown in the following
sequence.
(1) Set the interrupt enable bit to “0” (disabled) with CLB
instruction.
(2) Prepare serial I/O for transmission/reception.
(3) Set the interrupt request bit to “0” with CLB instruction
after 1 or more instruction has been executed.
(4) Set the interrupt enable bit to “1” (enabled).
<Reason>
When the transmission enable bit is set to “1”, the transmit buffer
empty flag and transmit shift register completion flag are set to
“1”.
The interrupt request is generated and the transmission interrupt
request bit is set regardless of which of the two timings listed
below is selected as the timing for the transmission interrupt to
be generated.
Transmit buffer empty flag is set to “1”
Transmit shift register completion flag is set to “1”
6. Transmission
control
when
external
clock
is
selected (Serial I/O1 clock synchronous mode)
When an external clock is used as the synchronous clock for data
transmission, set the transmit enable bit to “1” at “H” of the
SCLK1 input level. Also, write the transmit data to the transmit
buffer register (serial I/O shift register) at “H” of the SCLK1 input
level.
7. Transmit data writing (Serial I/O2)
In the clock synchronous serial I/O, when selecting an external
clock as synchronous clock, write the transmit data to the serial
I/O2 register (serial I/O shift register) at “H” of the transfer clock
input level.
Notes on PWM
The PWM starts after the PWM enable bit is set to enable and
“L” level is output from the PWM pin.
The length of this “L” level output is as follows:
n + 1
2
× f(XIN)
(s)
(Count source selection bit = “0”,
where n is the value set in the prescaler)
n + 1
f(XIN)
(s)
(Count source selection bit = “1”,
where n is the value set in the prescaler)
Can be set with the
LDM instruction at
the same time
Set the bits 0 to 3 and bit 6 of the serial I/O1
control register
Clear both the transmit enable bit (TE) and
the receive enable bit (RE) to “0”
Set both the transmit enable bit (TE) and the
receive enable bit (RE), or one of them to “1”
相关PDF资料 |
PDF描述 |
|---|---|
| MC68EN360RC33 | RISC MICROCONTROLLER, CPGA241 |
| MC56F8365MFG60 | 4-BIT, 120 MHz, OTHER DSP, PQFP128 |
| MPC8378ECVRANDA | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA689 |
| MB95F214KPH-G-SNE2 | 8-BIT, FLASH, MICROCONTROLLER, PDIP8 |
| MC9S12XS128J1VALR | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP112 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38507F8AFP#U1 | 功能描述:IC 740/3850 MCU FLASH 42SSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38507F8AFP#W1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 32K PB-FREE 42-SSOP T&R - Tape and Reel |
| M38507F8FP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 740 CISC 32KB Flash 5V 42-Pin SSOP 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#U1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#W1 | 制造商:Renesas Electronics Corporation 功能描述:FLASH 8-BIT 2.7 TO 5.5V PBFREE |
发布紧急采购，3分钟左右您将得到回复。