- 您现在的位置：买卖IC网 > PDF目录379298 > M68HC05M68H (Motorola, Inc.) HCMOS Microcontroller Unit PDF资料下载
参数资料
| 型号： | M68HC05M68H |
| 厂商： | Motorola, Inc. |
| 英文描述： | HCMOS Microcontroller Unit |
| 中文描述： | HCMOS微控制器 |
| 文件页数： | 87/130页 |
| 文件大小： | 1541K |
| 代理商： | M68HC05M68H |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页当前第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页
EPROM
Programming from an External Memory Device
MC68HC705P6A
—
Rev. 2.0
Advance Information
MOTOROLA
EPROM
87
10.8 Programming from an External Memory Device
In this programming mode, PC5 must be connected to V
SS
. PC4 and
PC3 are used to select the programming mode. The programming circuit
shown in
Figure 10-2
uses an external 12-bit counter to address the
memory device containing the code to be copied. This counter requires
a clock and a reset function. The 12-bit counter can address up to
4 Kbytes of memory, which means that a port pin has to be used to
address the remaining 4 K of the 8-K memory space.
The following procedure explains how to use the programming circuit
shown in
Figure 10-2
to copy a user program from an external memory
device into the MCU
’
s EPROM:
1.
Program a 2764-type EPROM device with the desired instructions
and data. Code programmed into the 2764 must appear at the
same addresses desired in the MC68HC705P6A. Therefore, the
page zero code must start at $0020 and end at $004F, the main
body of code must start at $0100 and end at $12FF, and the user
vectors must start at $1FF0 and end at $1FFF.
NOTE:
The MOR data must appear at $1EFF and $1F00.
2.
Install the programmed 2764 device into the programming circuit.
3.
Install the MC68HC705P6A to be programmed into the
programming circuit.
4.
Set the PROGRAM and/or VERIFY switches for the desired
operation (an open switch is the active state) and close the
RESET switch to hold the MCU in reset.
5.
Make sure that the V
PP
source is OFF.
Apply the V
DD
source to the programming circuit.
Apply the V
PP
source to the programming circuit.
Open the RESET switch to allow the MCU to come out of reset
and begin execution of the software in its internal bootloader
ROM.
6.
7.
8.
相关PDF资料 |
PDF描述 |
|---|---|
| M68HC11K | 8-BIT MICROCONTROLLER |
| M68HC711CFD | CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
| M68HC711CFG | CONFIG REGISTER PROGRAMMING FOR EEPROM-BASED MHC MICROCONTROLLERS |
| M68SDIL12 | The MC68HC912DT128A microcontroller unit (MCU) is a 16-bit device composed of standard on-chip peripherals including a 16-bit central processing unit |
| M68ADP912DG128PV | The MC68HC912DT128A microcontroller unit (MCU) is a 16-bit device composed of standard on-chip peripherals including a 16-bit central processing unit |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M68HC08 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| M68HC08M6 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:HCMOS Microcontroller Unit |
| M68HC08M68H | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:HCMOS Microcontroller Unit |
| M68HC11 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:CONFIG Register Programming for EEPROM-based M68HC11 Microcontrollers |
| M68HC11_03 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:8-channel, 8-bit analog-to-digital (A/D) converter |
发布紧急采购，3分钟左右您将得到回复。