- 您现在的位置：买卖IC网 > PDF目录9966 > MAX1038AEEE+T (Maxim Integrated Products)IC ADC 8BIT LP SERIAL 16-QSOP PDF资料下载
参数资料
| 型号： | MAX1038AEEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/23页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT LP SERIAL 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 8 |
| 采样率（每秒）： | 188k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1.75mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 12 个单端，单极；12 个单端，双极；6 个伪差分，单极；6 个伪差分，双极 |
MAX1036–MAX1039
in random access memory (RAM). If the scan mode is
set for multiple conversions, they all happen in succes-
sion with each additional result being stored in RAM.
The MAX1036/MAX1037 contain 8 bytes of RAM, and
the MAX1038/MAX1039 contain 12 bytes of RAM. Once
all conversions are complete, the MAX1036–MAX1039
release SCL, allowing it to be pulled high. The master
can now clock the results out of the output shift register
at a clock rate of up to 1.7MHz. SCL is stretched for a
maximum acquisition and conversion time of 7.6s per
channel (Figure 10).
The device RAM contains all of the conversion results
when the MAX1036–MAX1039 release SCL. The con-
verted results are read back in a first-in-first-out (FIFO)
sequence. If AIN_/REF is set to be a reference input or
output (SEL1 = 1, Table 6), AIN_/REF is excluded from
a multichannel scan. RAM contents can be read contin-
uously. If reading continues past the last result stored in
RAM, the pointer wraps around and points to the first
result. Note that only the current conversion results are
read from memory. The device must be addressed with
a read command to obtain new conversion results.
The internal clock mode’s clock stretching quiets the
SCL bus signal, reducing the system noise during con-
version. Using the internal clock also frees the master
(typically a microcontroller) from the burden of running
the conversion clock.
External Clock
When configured for external clock mode (CLK = 1),
the MAX1036–MAX1039 use SCL as the conversion
clock. In external clock mode, the MAX1036–MAX1039
begin tracking the analog input on the seventh falling
clock edge of a valid slave address byte. One SCL
clock cycle later, the analog signal is acquired and the
conversion begins. Unlike internal clock mode, convert-
ed data is available immediately after the slave-address
acknowledge bit. The device continuously converts
input channels dictated by the scan mode until given a
not acknowledge. There is no need to readdress the
device with a read command to obtain new conversion
results (Figure 11).
The conversion must complete in 9ms or droop on the
T/H capacitor degrades conversion results. Use internal
clock mode if the SCL clock period exceeds 1ms.
The MAX1036–MAX1039 must operate in external clock
mode for conversion rates up to 188ksps.
Scan Mode
SCAN0 and SCAN1 of the configuration byte set the
scan mode configuration. Table 5 shows the scanning
configurations. If AIN_/REF is set to be a reference input
or output (SEL1 = 1, Table 6), AIN_/REF is excluded
from a multichannel scan.
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
4-/12-Channel 2-Wire Serial 8-Bit ADCs
14
______________________________________________________________________________________
B. 2-BYTE WRITE CYCLE
SLAVE TO MASTER
MASTER TO SLAVE
S
1
SLAVE ADDRESS
A
71 1
W
SETUP OR
CONFIGURATION BYTE
SETUP OR
CONFIGURATION BYTE
8
P OR Sr
1
A
1
MSB DETERMINES WHETHER
SETUP OR CONFIGURATION BYTE
S
1
SLAVE ADDRESS
A
71 1
W
SETUP OR
CONFIGURATION BYTE
8
P OR Sr
1
A
1
MSB DETERMINES WHETHER
SETUP OR CONFIGURATION BYTE
A
1
8
A. 1-BYTE WRITE CYCLE
NUMBER OF BITS
Figure 9. Write Cycle
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72845LB15PFI | IC FIFO SYNC DL 4096X18 128TQFP |
| VI-211-MX-F1 | CONVERTER MOD DC/DC 12V 75W |
| VI-B3Z-MX | CONVERTER MOD DC/DC 2V 30W |
| HIN202CBNZ-T | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
| VI-21K-MX-F3 | CONVERTER MOD DC/DC 40V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1038EVKIT | 功能描述:数据转换 IC 开发工具 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1038KAEEE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1038LAEEE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1038MAEEE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1039 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
发布紧急采购，3分钟左右您将得到回复。