参数资料
型号: MAX1383ATP+T
厂商: Maxim Integrated Products
文件页数: 9/25页
文件大小: 0K
描述: IC ADC 12BIT 1.25MSPS 20-TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
位数: 12
采样率(每秒): 1.25M
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 2
功率耗散(最大): 85.5mW
电压电源: 单电源
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 20-WQFN 裸露焊盘
供应商设备封装: 20-TQFN-EP(5x5)
包装: 带卷 (TR)
输入数目和类型: 2 个单端,单极;2 个单端,双极;1 个差分,单极;1 个差分,双极
MAX1377/MAX1379/MAX1383
Dual, 12-Bit, 1.25Msps Simultaneous-Sampling
ADCs with Serial Interface
______________________________________________________________________________________
17
The internal reference is continuously powered-up dur-
ing both normal and partial power-down modes. In full
power-down mode, the internal reference is disabled.
Allow at least 2ms recovery time after a power-on reset
or exiting full power-down mode for the reference to
settle to its intended value.
Input Voltage Range (MAX1383)
The input range on the MAX1383 has an 8x relationship
with the reference voltage. For example, when the refer-
ence voltage (internal or external) is 2.5V, the input
range is ±10V (20VP-P).
External Reference Mode
Drive REFSEL high to select external reference mode.
Apply a reference voltage at REF. Bypass REF with
a 10nF capacitor and a 4.7F capacitor to RGND. As
with the internal reference, it is important to select a low
ESR capacitor and keep the trace resistance as low
as possible.
Serial Interface
Initialization After Power-Up
Upon initial power-up, the MAX1377/MAX1379/ MAX1383
require a complete conversion cycle to initialize the inter-
nal calibration. Following this initialization, the ADC is
ready for normal operation. This initialization is only
required after a hardware power-on reset and is not
required after exiting partial or full power-down mode.
Starting a Conversion and Reading the Output
With SCLK idling high or low, a falling edge on CNVST
begins a conversion (see Figure 6). This causes the
analog input stage to transition from track to hold
mode. SCLK provides the timing for the conversion
process, and data is shifted out as each bit of the result
is determined. A rising edge in CNVST forces the
device into one of three modes. The mode is deter-
mined by the clock cycle in which the transition occurs
and whether the device is set for single or dual outputs.
Figures 7 and 8 show each mode that is activated with
a rising CNVST edge for single and dual outputs.
CNVST
SCLK
DOUT_
tSETUP
tCL
tCH
tDHOLD
tDOUT
tCSW
CS
tACQ
D11
D10
D9
D8
D7
D6
D5
D4
D3
14
13
1
tCST
TRACKING
HOLD MODE
INTERNAL T/H STATE
D2
D1
D0
Figure 6. Detailed Serial-Interface Timing Diagram
CNVST
SCLK
1
2
3
4
14
28
POWER-DOWN
CONTINUOUS MODE
DOUT1 GOES HI-Z
DOUT1 HI-Z
29
CS
Figure 7. Single-Output CNVST Transition Modes
相关PDF资料
PDF描述
MS27484T20B39PC CONN PLUG 39POS STRAIGHT W/PINS
MS27467T21A41SA CONN PLUG 41POS STRAIGHT W/SCKT
D38999/26FG39PD CONN PLUG 39POS STRAIGHT W/PINS
V48B48M250BG3 CONVERTER MOD DC/DC 48V 250W
D38999/26FG39PC CONN PLUG 39POS STRAIGHT W/PINS
相关代理商/技术参数
参数描述
MAX1385AETM 制造商:Maxim Integrated Products 功能描述:12-BIT MULTI-CH ADC WITH MULTICH DA - Rail/Tube
MAX1385AETM+ 制造商:Maxim Integrated Products 功能描述:
MAX1385BETM 制造商:Maxim Integrated Products 功能描述:12-BIT MULTI-CH ADC WITH MULTICH DA - Rail/Tube
MAX1385BETM+ 功能描述:射频放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel
MAX1385BETM+T 功能描述:射频放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel