参数资料
型号: MAX1471ATJ+
厂商: Maxim Integrated
文件页数: 18/26页
文件大小: 0K
描述: IC RCVR ASK/FSK LP 32-TQFN
其它有关文件: Automotive Product Guide
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 60
频率: 315MHz,434MHz
灵敏度: -114dBm
调制或协议: ASK,FSK
应用: ISM,车库门开启器,RKE
电流 - 接收: 7mA
数据接口: PCB,表面贴装
天线连接器: PCB,表面贴装
电源电压: 3.3V,5V
工作温度: -40°C ~ 125°C
封装/外壳: 32-WFQFN 裸露焊盘
供应商设备封装: 32-TQFN-EP(5x5)
包装: 管件
315MHz/434MHz Low-Power, 3V/5V
ASK/FSK Superheterodyne Receiver
CS
SCLK
DIO
0
0
1
0
A3
A2
A1
A0
0
0
0
0
0
0
0
0
R7
R6
R5
R4
R3
R2
R1
R0
R7
R0
READ
COMMAND
ADDRESS
DATA
REGISTER DATA
REGISTER
DATA
16 BITS OF DATA
CS
SCLK
DIO
0
0
1
0
A3
A2
A1
A0
0
0
0
0
0
0
0
0
R7
R6
R5
R4
R3
R2
R1
A3
READ
COMMAND
ADDRESS
DATA
REGISTER DATA
8 BITS OF DATA
Figure 11. Read Command in 3-Wire Interface
Table 3. Command Bits
To calculate the value to write to register 0xA, use the
following equation and use the next integer higher than
C[3:0]
0x0
0x1
0x2
0x3
0x4–0xF
DESCRIPTION
No operation
Write data
Read data
Master reset
Not used
the calculated result:
Reg 0xA ≥ 3.3 x log 10 (Dwell Time x f XTAL )
For Manchester Code (50% duty cycle), set the dwell
time to at least twice the bit period. For nonreturn-to-
zero (NRZ) data, set the dwell to greater than the peri-
od of the longest string of zeros or ones. For example,
D well Time =
AGC Dwell Timer Register (Address: 0xA)
The AGC dwell timer holds the AGC in low-gain state
for a set amount of time after the power level drops
below the AGC switching threshold. After that set
amount of time, if the power level is still below the AGC
threshold, the LNA goes into high-gain state. This is
important for ASK since the modulated data may have
a high level above the threshold and a low level below
the threshold, which without the dwell timer would
cause the AGC to switch on every bit.
The AGC dwell time is dependent on the crystal fre-
quency and the bit settings of the AGC dwell timer reg-
ister. To calculate the dwell time, use the following
equation:
2 Reg0xA
f XTAL
where Reg 0xA is the value of register 0xA in decimal.
using Manchester code at 315MHz (f XTAL =
9.509375MHz) with a data rate of 4kbps (bit period =
125μs), the dwell time needs to be greater than 250μs:
Reg 0xA ≥ 3.3 x log 10 (250μs x 9.509375MHz) ≈ 11.14
Choose the register value to be the next integer value
higher than 11.14, which is 12 or 0x0C hex.
The default value of the AGC dwell timer on power-up
or reset is 0x0D.
Calibration
The MAX1471 must be calibrated to ensure accurate
timing of the off timer in discontinuous receive mode or
when receiving FSK signals. The first step in calibration
is ensuring that the oscillator frequency register
(address: 0x3) has been programmed with the correct
divisor value (see the Oscillator Frequency Register
section). Next, enable the mixer to turn the crystal dri-
ver on.
18
______________________________________________________________________________________
相关PDF资料
PDF描述
MICRF011BM IC RCVR/DATA DEMOD RF/IF 14SOIC
AMB310908 SENSOR REFL LONG H-TYPE
MICRF009BM IC RECEIVER UHF LOW POWER 16SOIC
MICRF007BM IC RECEIVER UHF LOW POWER 8SOIC
AMB345919 SENSOR REFL LONG V TYPE W/OSC
相关代理商/技术参数
参数描述
MAX1471ATJ/V+ 功能描述:射频接收器 315MHz/434MHz Low-Power 3V/5V ASK/FSK Superheterodyne Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ/V+T 功能描述:射频接收器 315MHz/434MHz Low-Power 3V/5V ASK/FSK Superheterodyne Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ+ 功能描述:射频接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ+T 功能描述:射频接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ-C3N 功能描述:射频接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel