参数资料
型号: MAX1471ATJ+
厂商: Maxim Integrated
文件页数: 21/26页
文件大小: 0K
描述: IC RCVR ASK/FSK LP 32-TQFN
其它有关文件: Automotive Product Guide
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 60
频率: 315MHz,434MHz
灵敏度: -114dBm
调制或协议: ASK,FSK
应用: ISM,车库门开启器,RKE
电流 - 接收: 7mA
数据接口: PCB,表面贴装
天线连接器: PCB,表面贴装
电源电压: 3.3V,5V
工作温度: -40°C ~ 125°C
封装/外壳: 32-WFQFN 裸露焊盘
供应商设备封装: 32-TQFN-EP(5x5)
包装: 管件
315MHz/434MHz Low-Power, 3V/5V
ASK/FSK Superheterodyne Receiver
Table 6. Power Configuration Register (Address: 0x0)
BIT ID
LNA_EN
AGC_EN
MIXER_EN
FSKBB_EN
FSKPD_EN
ASKBB_EN
ASKPD_EN
SLEEP
BIT NAME
LNA enable
AGC enable
Mixer enable
FSK baseband
enable
FSK peak
detector enable
ASK baseband
enable
ASK peak
detector enable
Sleep mode
BIT LOCATION
(0 = LSB)
7
6
5
4
3
2
1
0
POWER-UP
STATE
0
0
0
0
0
0
0
0
FUNCTION
1 = Enable LNA
0 = Disable LNA
1 = Enable AGC
0 = Disable AGC
1 = Enable mixer
0 = Disable mixer
1 = Enable FSK baseband
0 = Disable FSK baseband
1 = Enable FSK peak detectors
0 = Disable FSK peak detectors
1 = Enable ASK baseband
0 = Disable ASK baseband
1 = Enable ASK peak detectors
0 = Disable ASK peak detectors
1 = Deep-sleep mode
0 = Normal operation
At the end of t RF , the MAX1471 stops driving DIO low
and enables ADATA, FDATA, and peak detectors if
chosen to be active in the power configuration register
(0x0). The CPU must be awake at this point, and must
hold DIO low for the MAX1471 to remain in operation.
The CPU must begin driving DIO low any time during
t LOW = t CPU + t RF . If the CPU fails to drive DIO low,
DIO is pulled high through the internal pullup resistor,
and the timer sequence is restarted, leaving the
MAX1471 powered down. Any time the DIO line is dri-
ven high while the DRX = 1, the DRX sequence is initi-
ated, as defined in Figure 12.
t RF is a 16-bit timer, configured through registers 0x7
(upper byte) and 0x8 (lower byte). The possible t RF set-
tings are in Table 12. The data written to the t RF register
(0x7 and 0x8) is multiplied by 120μs to give the total t RF
time. On power-up, the RF timer registers are set to
zero and must be written before using DRX mode.
Typical Power-Up Procedure
Here is a typical power-up procedure for receiving either
ASK or FSK signals at 315MHz in continuous mode:
1) Write 0x3000 to reset the part.
2) Write 0x10FE to enable all RF and baseband sections.
3) Write 0x135F to set the oscillator frequency register
to work with a 315MHz crystal.
4) Write 0x1120 to set FSKCALLSB for an accurate
FSK calibration.
5) Write 0x1201 to begin FSK calibration.
6) Read 0x2900 and verify that bit 0 is 1 to indicate
FSK calibration is done.
The MAX1471 is now ready to receive ASK or FSK data.
Due to the high sensitivity of the receiver, it is recom-
mended that the configuration registers be changed
only when not receiving data. Receiver desensitization
may occur, especially if odd-order harmonics of the
SCLK line fall within the IF bandwidth.
______________________________________________________________________________________
21
相关PDF资料
PDF描述
MICRF011BM IC RCVR/DATA DEMOD RF/IF 14SOIC
AMB310908 SENSOR REFL LONG H-TYPE
MICRF009BM IC RECEIVER UHF LOW POWER 16SOIC
MICRF007BM IC RECEIVER UHF LOW POWER 8SOIC
AMB345919 SENSOR REFL LONG V TYPE W/OSC
相关代理商/技术参数
参数描述
MAX1471ATJ/V+ 功能描述:射频接收器 315MHz/434MHz Low-Power 3V/5V ASK/FSK Superheterodyne Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ/V+T 功能描述:射频接收器 315MHz/434MHz Low-Power 3V/5V ASK/FSK Superheterodyne Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ+ 功能描述:射频接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ+T 功能描述:射频接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX1471ATJ-C3N 功能描述:射频接收器 315MHz/434MHz Superheterodyne Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel