- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15002ATL+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM 40-TQFNEP PDF资料下载
参数资料
| 型号： | MAX15002ATL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/29页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 40-TQFNEP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 2.2MHz |
| 电源电压： | 5.5 V ~ 23 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
MAX15002
Dual-Output Buck Controller with
Tracking/Sequencing
Pin Description (continued)
PIN
20
21
22
23
24
25
26
27
28
29–33
34
35
36
37
38
39
40
—
10
NAME
DH2
BST2
CSN2
CSP2
ILIM2
COMP2
EN/TRACK2
FB2
PGOOD2
N.C.
SYNC
SGND
RT
PHASE
RESET
CT
IN
EP
FUNCTION
Controller 2 High-Side Gate Driver Output. DH2 drives the gate of the high-side MOSFET.
Controller 2 High-Side Gate Driver Supply. Connect BST2 to the cathode of the boost diode and to the
positive terminal of the boost capacitor.
Controller 2 Negative Current-Sense Input. Connect CSN2 to the synchronous MOSFET drain (connected to
LX2). When using a current-sense resistor, connect CSN2 to the junction of the low-side MOSFET’s source
and the current-sense resistor. See Figure 10.
Controller 2 Positive Current-Sense Input. Connect CSP2 to the synchronous MOSFET source (connected to
PGND2). When using a current-sense resistor, connect CSP2 to the PGND2 end of the current-sense
resistor.
Controller 2 Valley Current-Limit Set Output. Connect a 25k ? to 150k ? resistor, R ILIM2 , from ILIM2 to SGND
to program the valley current-limit threshold from 50mV to 300mV. ILIM2 sources 20μA out to R ILIM2 . The
resulting voltage divided by 10 is the valley current-limit threshold. When using a precision current-sense
resistor, connect a resistive divider from REG to ILIM2 to SGND to set the valley current limit. See Figure 10.
Controller 2 Error Transconductance Amplifier Output. Connect COMP2 to the compensation feedback
network.
Controller 2 Enable/Tracking Input. See Figure 2.
When sequencing, EN/TRACK2 must be above 1.24V for the PWM controller 2 to start.
Coincident tracking—connect the same resistive divider used for FB2, from Output 1 to EN/TRACK2 to
SGND.
Ratiometric tracking—connect EN/TRACK2 to analog ground.
Controller 2 Feedback Regulation Point. Connect to the center tap of a resistive divider from the converter
output to SGND to set the output voltage. The FB2 voltage regulates to V FB (0.6V).
Controller 2 Power-Good Output. Open-drain PGOOD2 output goes high impedance (releases) when FB2 is
above 0.925 x V FB (0.555V).
No Connection. Not internally connected.
Synchronization Input. Drive with a frequency at least 20% higher than two times the frequency
programmed using the RT pin. The switching frequency is 1/2 the SYNC frequency. Connect SYNC to
SGND when not used.
Analog Ground Connection. Connect SGND and PGND_ together at one point near the input bypass
capacitor return terminal.
Oscillator Timing Resistor Connection. Connect a 750k ? to 68k ? resistor from RT to SGND to program the
switching frequency from 200kHz to 2.2MHz.
Phase Select Input. Connect PHASE to SGND for 180° out-of-phase operation between the controllers.
Connect to REG for in phase operation.
RESET Output. Open-drain RESET output releases after all PGOODs are released and timeout programmed
by CT finishes.
RESET Timeout Capacitor Connection. Connect a timing capacitor from CT to analog ground to set the
RESET delay. CT sources 2μA into the timing capacitor. When the voltage at CT passes 2V, open-drain
RESET goes high impedance.
Supply Input Connection. Connect to an external voltage source from 5.5V to 23V. For 4.5V to 5.5V input
application, connect IN and REG together.
Exposed Pad. Solder the exposed pad to a large SGND plane.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15003ATM+T | IC REG CTRLR BUCK PWM 48TQFN-EP |
| MAX15005AAUE/V+ | IC REG CTRLR PWM CM 16-TSSOP |
| MAX15006BASA+ | IC REG LDO 5V 50MA 8-SOIC |
| MAX15008ATJ+ | IC REG LDO 5V/ADJ .3A 32TQFN-EP |
| MAX15009ATJ+ | IC REG LDO 5V/ADJ .3A 32TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15003ATM+ | 功能描述:DC/DC 开关控制器 Triple-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15003ATM+T | 功能描述:DC/DC 开关控制器 Triple-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15003EVKIT+ | 功能描述:电源管理IC开发工具 MAX15003 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15004AAUE/V+ | 功能描述:电流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX15004AAUE/V+T | 功能描述:电流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。