MAX15002
Dual-Output Buck Controller with
Tracking/Sequencing
Internal Undervoltage Lockout (UVLO)
V IN must exceed the default UVLO threshold before any
operation can commence. The UVLO circuitry keeps the
MOSFET drivers, oscillator, and all the internal circuitry
shut down to reduce current consumption. The UVLO
rising threshold is 4.05V with 350mV hysteresis.
Digital Soft-Start/Soft-Stop
The MAX15002 soft-start feature allows the load voltage
to ramp up in a controlled manner, eliminating output-
voltage overshoot. Soft-start begins after V IN exceeds
the undervoltage lockout threshold and the enable
input is above 1.24V. The soft-start circuitry gradually
ramps up the reference voltage. This controls the rate
of rise of the output voltage and reduces input surge
currents during startup. The soft-start duration is 2048
clock cycles. The output voltage is incremented
through 64 equal steps. The output reaches regulation
when soft-start is completed, regardless of output
capacitance and load.
Soft-stop commences when the enable input falls
below 1.12V. The soft-stop circuitry ramps down the
reference voltage controlling the output voltage rate of
fall. The output voltage is decremented through 64
equal steps in 2048 clock cycles.
Internal Linear Regulator (REG)
REG is the output terminal of a 5V LDO powered from IN
which provides power to the IC. Connect REG externally
to DREG_ to provide power for the low-side MOSFET
gate driver. Bypass REG to SGND with a minimum 2.2μF
ceramic capacitor. Place the capacitor physically close
to the MAX15002 to provide good bypassing. REG is
intended for powering only the internal circuitry and
should not be used to supply power to external loads.
REG can source up to 120mA. This current, I REG ,
includes quiescent current (I Q ) and gate drive current
(I DREG_ ):
I REG = I Q + [f SW x Σ (Q GHS_ + Q GLS_ )]
where Q GHS_ + Q GLS_ is the total gate charge of each
of the respective high- and low-side external MOSFETs
at V GATE = 5V. f SW is the switching frequency of the
converter and I Q is the quiescent current of the device
at the switching frequency.
Maxim Integrated
MOSFET Gate Drivers
DREG_ is the supply input for the low-side MOSFET dri-
ver. Connect DREG_ to REG externally. Everytime the
low-side MOSFET switches on, high peak current is
drawn from DREG_ for a short amount of time. Adding
an RC filter (1 ? to 3.3 ? and 2.2μF//0.1μF ceramic
capacitors are typical) from REG to DREG_ filters out
high-peak currents.
BST_ supplies the power for the high-side MOSFET dri-
vers. Connect the bootstrap diode from BST_ to DREG_
(anode at DREG_ and cathode at BST_). Connect a
bootstrap 0.1μF or higher ceramic capacitor between
BST_ and LX_. Though not always necessary, it may be
useful to insert a small resistor (4.7 ? to 22 ? ) in series
with the BST_ pin and the cathode of the bootstrap
diode for additional noise immunity.
The high-side (DH_) and low-side (DL_) drivers drive
the gates of the external n-channel MOSFETs. The dri-
vers’ 2A peak source- and sink-current capability pro-
vides ample drive for the fast rise and fall times of the
switching MOSFETs. Faster rise and fall times result in
reduced switching losses.
The gate driver circuitry also provides a break-before-
make time (20ns typ) to prevent shoot-through currents
during transition.
Oscillator/Synchronization Input/Phase
Staggering (RT, SYNC, PHASE)
Use an external resistor at RT to program the
MAX15002 switching frequency from 200kHz to
2.2MHz. Choose the appropriate resistor at RT to cal-
culate the desired output switching frequency (f SW ):
f SW (Hz) = 1.5 x 10 11 /(R RT + 2000) ?
Connect an external clock at SYNC for external clock
synchronization. A rising clock edge on SYNC is inter-
preted as a synchronization input. If the SYNC signal is
lost, the internal oscillator takes control of the switching
rate, returning the switching frequency to that set by
R RT . This maintains output regulation even with intermit-
tent SYNC signals. For proper synchronization, the
external frequency must be at least 20% higher than
twice the frequency programmed through the RT input.
The switching frequency is 1/2 the SYNC frequency.
Connect SYNC to SGND when not used.
Connect PHASE to SGND for 180° out-of-phase opera-
tion between the controllers. Connect PHASE to REG
for in-phase operation.
13