- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1531ETJ/V+T (Maxim Integrated Products)IC PS CTRLR MULTI-OUTPUT 32WQFN PDF资料下载
参数资料
| 型号： | MAX1531ETJ/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/33页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR MULTI-OUTPUT 32WQFN |
| 标准包装： | 2,500 |
| 应用： | 五路电源监控器 |
| 电源电压： | 4.5 V ~ 28 V |
| 电流 - 电源： | 1.7mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Multiple-Output Power-Supply
Controllers for LCD Monitors
LR2 is typically used to generate the TFT LCD gamma
reference voltage, which is usually 0.3V below the
source drive supply voltage.
LR2 is enabled when the step-down regulator is
enabled and the voltage on ONL2 exceeds ONL2 input
threshold (1.238V typ). (See the Startup Sequence
(ONL_,SEQ) section.) Each time it is enabled, the con-
troller goes through a soft-start routine that ramps up its
internal reference DAC. (See the Soft-Start section).
Linear Regulator Controller (LR3)
LR3 is an analog gain block with an open-drain N-
channel output. It drives an external PNP pass transis-
tor with a 6.8k Ω base-to-emitter resistor. Its guaranteed
base drive sink current is at least 2mA. The regulator,
including Q3 in Figure 1, uses a 0.47μF output capaci-
tor and is designed to deliver 20mA at 25V. The regula-
tor including Q3 in Figure 2 uses a 4.7μF output
capacitor and is designed to deliver 500mA at 10V.
For the MAX1531 (Figure 1), LR3 is typically used to gen-
erate the TFT LCD gate driver’s gate-on voltage. A suffi-
cient input voltage can be produced using a
charge-pump circuit as shown in Figure 1. Note that the
voltage rating of the DRV3 output is 28V. If higher volt-
ages are present, an external cascode NPN transistor
(Q6) should be used with the emitter connected to
DRV3, the base to V IN (which is the connection point of
C1 and R12 in Figure 1), and the collector to the base of
the PNP pass transistor (Figure 1). For the MAX1530
(Figure 2), LR3 is typically used to generate the TFT LCD
source drive supply voltage. The input for this regulator
can come directly from the input supply, be produced
from an external step-up regulator, or from an extra wind-
ing coupled to the main step-down regulator inductor.
LR3 is enabled when the step-down regulator is
enabled and the voltage on ONL3 exceeds the ONL3
input threshold (1.238V typ). (See the Startup Sequence
(ONL_,SEQ) section.) Each time it is enabled, the con-
troller goes through a soft-start routine that ramps up its
internal reference DAC. (See the Soft-Start section.)
Source Drive Regulator Controller (LR4)
(MAX1531 Only)
LR4 is an analog gain block with an open-drain N-
channel output. It drives an external PNP pass transis-
tor with a 1.5k Ω base-to-emitter resistor. Its guaranteed
base drive sink current is at least 10mA. The regulator
including Q4 in Figure 1 uses a 4.7μF output capacitor
and is designed to deliver 500mA at 10V. The regula-
tor’s fast transient response allows it to handle brief
peak currents up to 2A.
LR4 is typically used to generate the TFT LCD source
drive supply voltage. The input for this regulator can
come directly from the input supply, be produced from
an external step-up regulator, or from an extra winding
coupled to the main step-down regulator inductor.
LR4 is enabled when the step-down regulator is
enabled and the voltage on ONL4 exceeds the ONL4
input threshold (1.238V typ). (See the Startup
Sequence (ONL_,SEQ) section.) Each time it is
enabled, the regulator goes through a soft-start routine
that ramps up its internal reference DAC from 0V to
1.238V (typ). (See the Soft-Start section.)
The standard application circuit in Figure 1 powers the
LR4 regulator directly from the input supply and uses
the MAX1531’s general-purpose overcurrent protection
function to protect the input supply from excessive load
currents. (See the Overcurrent Protection section.)
Gate-Off Regulator Controller (LR5) (MAX1531 Only)
LR5 is an analog gain block with an open-drain P-chan-
nel output. It drives an external NPN pass transistor
with a 6.8k Ω base-to-emitter resistor. Its guaranteed
base drive sink current is at least 2mA. The regulator
including Q5 in Figure 1 uses a 0.47μF output capacitor
and is designed to deliver 10mA at -10V.
LR5 is typically used to generate the TFT LCD gate dri-
ver’s gate-off voltage. A negative input voltage can be
produced using a charge-pump circuit as shown in
Figure 1. Use as many stages as necessary to obtain
the required output voltage.
LR5 is enabled when the step-down regulator is
enabled and the voltage on ONL5 exceeds the ONL5
input threshold (1.238V typ). (See the Startup
Sequence (ONL_,SEQ) section.) Each time it is
enabled, the regulator goes through a soft-start routine
that ramps down its internal reference DAC from VL to
125mV (typ). (See the Soft-Start section.)
Internal 5V Linear Regulator (VL)
All MAX1530/MAX1531 functions, except the thermal
sensor, are internally powered from the on-chip, low-
dropout 5V regulator. The maximum regulator input
voltage (V IN ) is 28V. Bypass the regulator’s output (VL)
with at least a 1μF ceramic capacitor to AGND. The
V IN -to-VL dropout voltage is typically 200mV, so when
V IN is less than 5.2V, VL is typically V IN - 200mV. The
internal linear regulator can source up to 30mA to sup-
ply the device, power the low-side gate driver, charge
the external boost capacitor, and supply small external
loads. When driving particularly large MOSFETs, little or
no regulator current may be available for external
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1533AETJ+ | IC POWER SUPPLY CONTROLER 32TQFN |
| MAX1533ETJ+ | IC POWER SUPPLY CONTROLER 32TQFN |
| MAX1534ETE+ | IC PWR SUPPLY CONTROLLER 16TQFN |
| MAX1536ETI+ | IC REG BUCK SYNC ADJ 3.6A 28TQFN |
| MAX1538ETI+T | IC PWR SOURCE SELECTOR 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1531EVKIT | 功能描述:电源管理IC开发工具 MAX1530/1 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX1532AETL | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1532AETL+ | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1532AETL+T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MULTIPLE OUTPUT POWER-SUPPLY CTRL |
| MAX1532AETL-T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。