- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1531ETJ/V+T (Maxim Integrated Products)IC PS CTRLR MULTI-OUTPUT 32WQFN PDF资料下载
参数资料
| 型号： | MAX1531ETJ/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/33页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR MULTI-OUTPUT 32WQFN |
| 标准包装： | 2,500 |
| 应用： | 五路电源监控器 |
| 电源电压： | 4.5 V ~ 28 V |
| 电流 - 电源： | 1.7mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Multiple-Output Power-Supply Controllers for
LCD Monitors
loads. For example, when switched at 500kHz, large
MOSFETs with a total of 40nC total gate charge would
require 40nC × 500kHz, which is approximately 20mA.
On/Off Control (EN)
EN > 1.24V
AND
VL > 3.5V
SEQ = HIGH
The EN pin has an accurate 1.238V (typ) rising thresh-
old with 5% hysteresis. The accurate threshold allows it
STEP-DOWN
REGULATOR
STARTUP
SEQUENCE
BLOCK
ENABLED
ONL_
CURRENT
SOURCES ON
to be used to monitor the input voltage or other analog
signals of interest. If V EN voltage is less than its thresh-
old, then the step-down regulator and all linear regula-
STEP-DOWN
SOFT-START
tors are turned off. VL and the internal reference remain
active when EN is low to allow an accurate EN thresh-
LR1
DONE
ONL2 > 1.24V
LR2
ONL3 > 1.24V
LR3
ONL4 > 1.24V
LR4
ONL5 > 1.24V
LR5
old. A rising edge on the pin clears any latched faults
STARTUP
STARTUP
STARTUP
STARTUP
STARTUP
except for a thermal fault, which is cleared only by
cycling the input power.
Figure 5. Startup Conditions
Undervoltage Lockout
If VL drops below 3.4V (typ), the MAX1530/MAX1531
assume that the supply voltage is too low to make valid
ONLa
R3
150k Ω
ONLb
R2
75k Ω
ONLc
R1
51k Ω
ONLd
decisions. Therefore, the undervoltage lockout (UVLO)
circuitry turns off all the internal bias supplies. Switching
is inhibited, and the DL and DH gate drivers are forced
low. After VL rises above 3.5V (typ), the fault and thermal
C1
0.1 μ F
shutdown latches are cleared and startup begins if EN is
above its threshold.
SEQ
5V
ONLa ONLb ONLc
ONLd
Startup Sequence (ONL_, SEQ)
The MAX1530/MAX1531 are not enabled unless all four
of the following conditions are met: 1) VL exceeds the
UVLO threshold, 2) EN is above 1.238V, 3) the fault
latch is not set, and 4) the thermal shutdown latch is not
set. After all four conditions are met, the step-down con-
troller starts switching and enables soft-start (Figure 5).
After the step-down regulator soft-start is done, the low-
1.238V
ONL_
voltage logic linear regulator controller (LR1) soft-starts.
0V
ON
The remaining linear regulator controllers and the
sequence block that can be used to control them are
enabled at the same time as the step-down regulator.
The SEQ logic input is used in combination with the
ONL_ pins to control the startup sequence. When SEQ
is high and the sequence block is enabled, each ONL_
pin sources 2μA (typ). When the voltage on an ONL_
pin reaches 1.238V (typ), its respective linear regulator
LRa
LRb
LRc
LRd
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
controller (LR_) is enabled. When SEQ is low or the
sequence block is not enabled, each ONL_ pin is con-
nected to ground through a 1.5k Ω internal MOSFET.
The sequence block allows the user to program the
startup of LR2 to LR5 in any desired sequence. If no
capacitor is placed on an ONL_ pin, its LR_ controller
starts immediately after the sequence block is enabled
and SEQ goes high. Placing a 1.5nF capacitor on an
ONL_ pin provides about 1ms delay for the respective
16ms
Figure 6. Single-Capacitor Sequence Configuration
LR_ controller. Placing different size capacitors on
each ONL_ pin allows any arbitrary startup sequence.
An arbitrary startup sequence can also be created with
a single capacitor (Figure 6). Capacitor C1, together
with the 8μA current (2μA per ONL_ pin), is chosen to
provide the desired delay for the controller that starts
last (ONLd). Using 0.1μF for C1 provides about 16ms
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1533AETJ+ | IC POWER SUPPLY CONTROLER 32TQFN |
| MAX1533ETJ+ | IC POWER SUPPLY CONTROLER 32TQFN |
| MAX1534ETE+ | IC PWR SUPPLY CONTROLLER 16TQFN |
| MAX1536ETI+ | IC REG BUCK SYNC ADJ 3.6A 28TQFN |
| MAX1538ETI+T | IC PWR SOURCE SELECTOR 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1531EVKIT | 功能描述:电源管理IC开发工具 MAX1530/1 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX1532AETL | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1532AETL+ | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1532AETL+T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MULTIPLE OUTPUT POWER-SUPPLY CTRL |
| MAX1532AETL-T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。