- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1531ETJ/V+T (Maxim Integrated Products)IC PS CTRLR MULTI-OUTPUT 32WQFN PDF资料下载
参数资料
| 型号： | MAX1531ETJ/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/33页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR MULTI-OUTPUT 32WQFN |
| 标准包装： | 2,500 |
| 应用： | 五路电源监控器 |
| 电源电压： | 4.5 V ~ 28 V |
| 电流 - 电源： | 1.7mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页
Multiple-Output Power-Supply
Controllers for LCD Monitors
amount of ripple after the PC board layout has been
optimized, consider increasing output capacitance.
Adding more capacitance does not eliminate the ripple,
but proportionally reduces the amplitude of the ripple. If
increasing the output capacitance is not desirable
because of space or cost concerns, then consider
slowing the turn-on of the step-down DC-to-DC
MOSFETs. Slower turn-on leads to smoother LX rising
amplifier delay, the pass transistor’s input capacitance,
and the stray capacitance at the feedback node create
additional poles in the system, and the output capacitor’s
ESR generates a zero. For proper operation, use the fol-
lowing steps to ensure the linear regulator’s stability:
1) First, calculate the dominant pole set by the linear
regulator’s output capacitor and the load resistor:
and falling edges and consequently reduces the
switching noise. When slowing down MOSFET turn-on,
ensure the turn-off time is not affected. Otherwise, the
f POLE ( LR ) =
1
2 π C LR R LOAD
adaptive dead-time circuitry may not work properly and
shoot-through may occur. See the MOSFET Gate
Drivers section for details on how to slow down the
turn-on of both DH and DL.
Stability Requirements
The MAX1530/MAX1531 linear-regulator controllers use
an internal transconductance amplifier to drive an
external pass transistor. The transconductance amplifi-
er, the pass transistor, the base-emitter resistor, and
the output capacitor determine loop stability. The fol-
lowing applies equally to all linear regulators in the
MAX1530 and MAX1531. Any differences are highlight-
ed where appropriate.
The transconductance amplifier regulates the output
voltage by controlling the pass transistor’s base cur-
where C LR is the output capacitance of the linear
regulator and R LOAD is the load resistance corre-
sponding to the maximum load current.
The unity-gain crossover of the linear regulator is:
f CROSSOVER = A V ( LDO ) f POLE ( LDO )
2) The pole created by the internal amplifier delay is
about 1MHz:
f POLE ( AMP ) ? 1 MHz
3) Next, calculate the pole set by the transistor’s input
capacitance, the transistor’s input resistance, and
the base-to-emitter pullup resistor:
× 1 + BIAS FE ? × V REF
A V ( LR ) ≈ ?
rent. The total DC loop gain is approximately:
? 4 ? ? I × h ?
? ?
? V T ? ? I LOAD ?
f POLE ( C IN ) =
1
2 π C IN ( R BE || R IN )
, R IN = R π = FE , g m is the
where V T is 26mV at room temperature, I LOAD is the
output current of the linear regulator, V REF is the linear
where C IN =
g m
2 π f T
h
g m
regulator’s internal reference voltage, and I BIAS is the
current through the base-to-emitter resistor (R BE ). Each
of the linear regulator controllers is designed for a dif-
ferent maximum output current so they have different
output drive currents and different bias currents (I BIAS ).
Each controller ’s bias current can be found in the
transconductance of the pass transistor, and f T is the
transition frequency. Both parameters can be found
in the transistor’s data sheet.
Because R BE is much greater than R IN , the above
equation can be simplified:
Electrical Characteristics . The current listed in the
Conditions column for the FBL_ regulation voltage
specification is the individual controller’s bias current.
f POLE ( C IN ) ≈
1
2 π C IN R IN
The base-to-emitter resistor for each controller should
be chosen to set the correct I BIAS :
The equation can be further simplified:
f POLE ( C IN ) = T
R BE =
V BE
I BIAS
f
h FE
The output capacitor and the load resistance create the
dominant pole in the system. However, the internal
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1533AETJ+ | IC POWER SUPPLY CONTROLER 32TQFN |
| MAX1533ETJ+ | IC POWER SUPPLY CONTROLER 32TQFN |
| MAX1534ETE+ | IC PWR SUPPLY CONTROLLER 16TQFN |
| MAX1536ETI+ | IC REG BUCK SYNC ADJ 3.6A 28TQFN |
| MAX1538ETI+T | IC PWR SOURCE SELECTOR 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1531EVKIT | 功能描述:电源管理IC开发工具 MAX1530/1 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX1532AETL | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1532AETL+ | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1532AETL+T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel 制造商:Maxim Integrated Products 功能描述:MULTIPLE OUTPUT POWER-SUPPLY CTRL |
| MAX1532AETL-T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。