- 您现在的位置：买卖IC网 > PDF目录17275 > MAX17080EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX17080 PDF资料下载
参数资料
| 型号： | MAX17080EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/48页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX17080 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 3，非隔离 |
| 输入电压： | 4 ~ 26 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX17080 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
Pin Description (continued)
PIN
14
NAME
GNDS2
FUNCTION
SMPS2 Remote Ground-Sense Input. Normally connected to GND directly at the load. GNDS2
internally connects to a transconductance amplifier that fine tunes the output voltage—
compensating for voltage drops from the SMPS ground to the load ground.
Connect GNDS1 or GNDS2 above 0.9V combined-mode operation (unified core). When GNDS2 is
pulled above 0.9V, GNDS1 is used as the remote ground-sense input.
Output of the Voltage-Positioning Transconductance Amplifier for SMPS2. The R and C network
between this pin and the positive side of the remote-sensed output voltage sets the transient AC
droop:
15
FBAC2
R DROOP_AC2 =
R FBAC2 × R FBDC2
R FBAC2 + R FBDC2 + R FB22 Z CFB 2
× R SENSE2 × Gm (FBAC2)
where R DROOP_AC2 is the transient (AC) voltage-positioning slope that provides an acceptable
trade-off between stability and load-transient response, Gm (FBAC2) = 2mS (typ), R SENSE2 is the
value of the current-sense element that is used to provide the (CSP2, CSN2) current-sense voltage,
Z CFB2 is the impedance of C FB2 .
FBAC2 is high impedance in shutdown.
Feedback-Sense Input for SMPS2. Connect a resistor R FBDC2 between FBDC2 and the positive side
of the feedback remote sense, and a capacitor from FBAC2 to couple the AC ripple from FBAC2 to
FBDC2. An integrator on FBDC2 corrects for output ripple and ground-sense offset.
16
17
18
19
FBDC2
CSN2
CSP2
PGD_IN
To enable a DC load-line less than the AC load-line, add a resistor from FBAC2 to FBDC2.
To enable a DC load-line equal to the AC load-line, short FBAC2 to FBDC2. See the Core Steady-
State Voltage Positioning (DC Droop) section.
FBDC2 is high impedance in shutdown.
Negative Current-Sense Input for SMPS2. Connect to the negative side of the output current-sensing
resistor or the filtering capacitor if the DC resistance of the output inductor is utilized for current
sensing.
A 20
discharge FET is enabled from CSN2 to PGND when the SMPS2 is shut down.
Positive Current-Sense Input for SMPS2. Connect to the positive side of the output current-sensing
resistor or the filtering capacitor if the DC resistance of the output inductor is utilized for current
sensing.
System Power-Good Input.
PGD_IN is low when SHDN first goes high. The MAX17080 decodes the 2 SVI bits to determine the
boot voltage. The SVI bits can be changed dynamically during this time while PGD_IN remains low
and PWRGD is still low.
PGD_IN goes high after the MAX17080 reaches the boot voltage. This indicates that the SVI block
is active, and the MAX17080 starts to respond to the SVI commands. The MAX17080 stores the
boot VID when PWRGD first goes high. The stored boot VID is cleared by rising SHDN .
After PGD_IN has gone high, if at any time PGD_IN goes low, the MAX17080 regulates to the
previously stored boot VID. PWRGD is forced low until the internal DAC reaches the stored boot VID
plus an additional 20μs. The slew rate during this transition is set by the resistor between the TIME
and GND pins.
The subsequent rising edge of PGD_IN does not change the stored VID.
PWRGD is independent of PGD_IN.
______________________________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| ECC20DCMD | CONN EDGECARD 40POS .100 WW |
| TDL825K020S1B | CAP TANT 8.2UF 20V 10% RADIAL |
| 100R28-76B | CABLE FLAT FLEX 28POS 1MM 3" |
| EBM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
| TDL106K020S1C-F | CAP TANT 10UF 20V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080EVKIT+ | 功能描述:电源管理IC开发工具 MAX17080 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。