- 您现在的位置：买卖IC网 > PDF目录17275 > MAX17080EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX17080 PDF资料下载
参数资料
| 型号： | MAX17080EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/48页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX17080 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 3，非隔离 |
| 输入电压： | 4 ~ 26 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX17080 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
Nominal Output-Voltage Selection
Table 3. Boot Voltage Code Table
Core SMPS Output Voltage
The nominal no-load output voltage (V TARGET_ ) for
each SMPS is defined by the selected voltage refer-
ence (VID DAC) plus the remote ground-sense adjust-
ment (V GNDS ) and the offset voltage (V OFFSET ) as
defined in the following equation:
V TARGET = V FBDC = V DAC + V GNDS + V OFFSET
SVC
0
0
1
1
SVD
0
1
0
1
BOOT VOLTAGE
V OUT (V)
1.1
1.0
0.9
0.8
where V DAC is the selected VID voltage of the core
SMPS DAC, V GNDS is the ground-sense correction volt-
age for core supplies, and V OFFSET is the +12.5mV off-
set enabled by the OPTION pin when the PSI_L is set
high for core supplies.
NB SMPS Output Voltage
The nominal output voltage (V TARGET ) for the NB is
defined by the selected voltage reference (VID DAC)
plus the offset voltage (V OFFSET_NB ) as defined in the
following equation:
V TARGET 3 = V OUT 3 = V DAC + V OFFSET _ NB
where V DAC is the selected VID voltage of the NB DAC,
and V OFFSET_NB is +12.5mV or +6.25mV as set by the
ILIM3 pin for NB.
7-Bit DAC
Inside the MAX17080 are three 7-bit digital-to-analog
converters (DACs). Each DAC can be individually pro-
grammed to different voltage levels by the serial-inter-
face bus. The DAC sets the target for the output voltage
for the core and NB SMPSs. The available DAC codes
and resulting output voltages are compatible with the
AMD SVI (Table 4) specifications.
Boot Voltage
On startup, the MAX17080 slews the target for all three
DACs from ground to the boot voltage set by the SVC
and SVD pin-voltage levels. While the output is still below
regulation, the SVC and SVD levels can be changed,
and the MAX17080 sets the DACs to the new boot volt-
age. Once the programmed boot voltage is reached and
PWRGD goes high, the MAX17080 stores the boot VID.
Changes in the SVC and SVD settings do not change the
output voltage once the boot VID is stored. When
PGD_IN goes high, the MAX17080 exits boot mode, and
the three DACs can be independently set to any voltage
in the VID table by the serial interface.
If PGD_IN goes from high to low any time after the boot
VID is stored, the MAX17080 sets all three DACs back
to the voltage of the stored boot VID.
Table 3 is the boot voltage code table.
Core SMPS Offset
A +12.5mV offset can be added to both core SMPS
DAC voltages for applications that include DC droop.
The offset is applied only after the MAX17080 exits boot
mode (PGD_IN going from low to high), and the
MAX17080 enters the serial-interface mode. The offset
is disabled when the PSI_L bit is set, saving more
power when the load is light.
The OPTION pin setting enables or disables the
+12.5mV offset. Connect OPTION to OSC (2V) or GND
to enable the offset. Keep OPTION connected to 3.3V
or V CC to disable the offset. See the Offset and
Address Change for Core SMPSs (OPTION) section.
NB SMPS Offset
The NB SMPS output has a -6.5mV/A load-line. An off-
set is required to keep the output within regulation over
the full load. The offset is set by the ILIM3 pin setting
(see Table 7). Connect ILIM3 to OSC (2V) or GND to
set a +6.25mV offset. Pull the ILIM3 pin up to 3.3V or
V CC to set +12.5mV offset. See the Offset and Current-
Limit Setting for NB SMPS (ILIM3) section.
Output-Voltage Transition Timing
SMPS Output-Voltage Transition
The MAX17080 performs positive voltage transitions in
a controlled manner, automatically minimizing input
surge currents. This feature allows the circuit designer
to achieve nearly ideal transitions, guaranteeing just-in-
time arrival at the new output-voltage level with the low-
est possible peak currents for a given output
capacitance. The slew rate (set by resistor R TIME ) must
be set fast enough to ensure that the transition is com-
pleted within the maximum allotted time for proper CPU
operation. R TIME is between 35.7k ? and 357k ? for cor-
responding slew rates between 25mV/μs to 2.5mV/μs,
respectively, for the SMPSs.
At the beginning of an output-voltage transition, the
MAX17080 blanks both PWRGD comparator thresholds,
preventing the PWRGD open-drain output from chang-
ing states during the transition. At the end of an upward
VID transition, the controller enables both PWRGD
thresholds approximately 20μs after the slew-rate
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| ECC20DCMD | CONN EDGECARD 40POS .100 WW |
| TDL825K020S1B | CAP TANT 8.2UF 20V 10% RADIAL |
| 100R28-76B | CABLE FLAT FLEX 28POS 1MM 3" |
| EBM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
| TDL106K020S1C-F | CAP TANT 10UF 20V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080EVKIT+ | 功能描述:电源管理IC开发工具 MAX17080 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。