- 您现在的位置：买卖IC网 > PDF目录17275 > MAX17080EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX17080 PDF资料下载
参数资料
| 型号： | MAX17080EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/48页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX17080 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 3，非隔离 |
| 输入电压： | 4 ~ 26 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX17080 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
? I L R SENSE Gm ( FBAC ) R FBDC + ? I L R ESR
≤ 28 mV
( 56 mV - ? I L ESR ) ( R FBAC + R F B )
R FBDC ≤
V OUT ( MAX ) ( V IN ( MAX ) ? V OUT ( MAX ) )
Transient Phase Repeat
When a transient occurs, the output voltage deviation
depends on the controller’s ability to quickly detect the
transient and slew the inductor current. A fixed-frequency
controller typically responds only when a clock edge
occurs, resulting in a delayed transient response. To
minimize this delay time, the MAX17080 includes
enhanced transient detection and transient phase
repeat capabilities. If the controller detects that the out-
put voltage has dropped by 38mV, the transient detec-
tion comparator immediately retriggers the phase that
completed its on-time last. The controller triggers the
subsequent phases as normal, on the appropriate
oscillator edges. This effectively triggers a phase a full
cycle early, increasing the total inductor-current slew
rate and providing an immediate transient response.
Core SMPS Feedback
Adjustment Amplifiers
The MAX17080 provides an FBAC and FBDC pin for
each SMPS to allow for flexible AC and DC droop set-
tings. FBAC is the output of an internal transconduc-
tance amplifier that outputs a current proportional to the
current-sense signal. FBDC is the feedback input that is
compared against the internal target. Place resistors
and capacitors at the FBAC and FBDC pins as shown
in Figure 4. With this configuration, the DC droop is
always less than or equal to the AC droop.
MAX17080
I FBAC = Gm ( FBAC ) V CS
where V CS = V CSP - V CSN is the differential current-sense
voltage, and Gm (FBAC) is typically 2mS as defined in the
Electrical Characteristics table. DC droop is typically used
together with the +12.5mV offset feature to keep within the
DC tolerance window of the application. See the Offset
and Address Change for Core SMPSs (OPTION) section.
The ripple voltage on FBDC must be less than the -28mV
(max) transient phase repeat threshold:
R FBAC
R FBAC + R FBDC + R FB
2
R
R FBAC ? I L R SENSE Gm ( FBAC ) - 56 mV
where ? I L is the inductor ripple current, R ESR is the
effective output ESR at the remote sense point, R SENSE
is the current-sense element, and Gm (FBAC) is 2.06mS
(max) as defined in the Electrical Characteristics table.
The worst-case inductor ripple occurs at the maximum
input-voltage and maximum output-voltage conditions:
? I L ( MAX ) =
V IN ( M A X ) f SW L
To make the DC and AC load-lines the same, directly
short FBAC to FBDC.
To disable DC voltage positioning, remove R FB , which
connects FBAC to FBDC.
Core Transient Voltage-Positioning Amplifier
CSP
CSN
Gm (FBAC)
FBAC
C FB
R FB
R FBAC
(AC Droop)
Each of the MAX17080 core supply SMPSs includes one
transconductance amplifier for voltage positioning. The
ERROR
AMP
FBDC
R FBDC
100 ?
CORE SENSE_H
amplifiers’ inputs are generated by summing their respec-
tive current-sense inputs, which differentially sense the
4700pF
voltage across either current-sense resistor or the induc-
TARGET
AGND
tor’s DCR.
The voltage-positioning amplifier’s output (FBAC) con-
Figure 4. MAX17080 Core SMPS Feedback Connection
Core Steady-State Voltage Positioning (DC Droop)
nects to the remote-sense point of the output through
an R and C network that sets each phase’s AC voltage-
positioning gain:
FBDC is the feedback input to the error amplifier.
Based on the configuration in Figure 4, the core SMPS
output voltage is given by:
V OUT = V TARGET -
R FBDC × R FBAC
R FBAC + R FBDC + R FB Z CF B
I FBAC
V OUT = V TARGET ?
R FBDC × R FBAC
R FBAC + R FBDC + R FB
× I FB A C
where the target voltage (V TARGET ) is defined in the
Nominal Output-Voltage Selection section, Z CFB is the
effective impedance of C FB , and the FBAC amplifier’s
where the target voltage (V TARGET ) is defined in the
Nominal Output-Voltage Selection section, and the
FBAC amplifier’s output current (I FBAC ) is determined
by each phase’s current-sense voltage:
output current (I FBAC ) is determined by each phase’s
current-sense voltage:
I FBAC = Gm ( FBAC ) V CS
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| ECC20DCMD | CONN EDGECARD 40POS .100 WW |
| TDL825K020S1B | CAP TANT 8.2UF 20V 10% RADIAL |
| 100R28-76B | CABLE FLAT FLEX 28POS 1MM 3" |
| EBM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
| TDL106K020S1C-F | CAP TANT 10UF 20V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080EVKIT+ | 功能描述:电源管理IC开发工具 MAX17080 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。