- 您现在的位置：买卖IC网 > PDF目录17275 > MAX17080EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX17080 PDF资料下载
参数资料
| 型号： | MAX17080EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/48页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX17080 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 3，非隔离 |
| 输入电压： | 4 ~ 26 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX17080 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
Pin Description (continued)
PIN
20
21
22
23
24
25
26
27
28
29
30
31
32
NAME
PWRGD
DH2
LX2
BST2
DL2
V DD
DL1
BST1
LX1
DH1
VRHOT
THRM
V CC
FUNCTION
Open-Drain Power-Good Output. PWRGD is the wired-OR open-drain output of all three SMPS
outputs.
PWRGD is forced high impedance whenever the slew-rate controller is active (output voltage
transitions).
During startup, PWRGD is held low for an additional 20μs after the MAX17080 reaches the startup
boot voltage set by the SVC and SVD pins. The MAX17080 stores the boot VID when PWRGD first
goes high. The stored boot VID is cleared by rising SHDN .
PWRGD is forced low in shutdown.
When SMPS is in pulse-skipping mode, the upper PWRGD threshold comparator for the respective
SMPS is blanked during a downward VID transition. The upper PWRGD threshold comparator is re-
enabled once the output is in regulation (Figure 5).
If PGD_IN goes low anytime after the boot sequence, PWRGD is forced low during the time when
any one of the three internal DACs is slewing from the current VID to the stored boot VID plus an
additional 20μs.
SMPS2 High-Side Gate-Driver Output. DH2 swings from LX2 to BST2. Low in shutdown.
SMPS2 Inductor Connection. LX2 is the internal lower supply rail for the DH2 high-side gate driver.
Also used as an input to SMPS2 ’s zero-crossing comparator.
Boost Flying Capacitor Connection for the DH2 High-Side Gate Driver. An internal switch between
V DD and BST2 charges the flying capacitor during the time the low-side FET is on.
SMPS2 Low-Side Gate-Driver Output. DL2 swings from GND2 to V DD . DL2 is forced low in shutdown.
DL2 is also forced high when an output overvoltage fault is detected. DL2 is forced low in skip
mode after an inductor current zero crossing (GND2 - LX2) is detected.
Supply Voltage Input for the DL_ Drivers. V DD is also the supply voltage used to internally recharge
the BST_ flying capacitors during the off-time. Connect V DD to the 4.5V to 5.5V system supply
voltage. Bypass V DD to GND with a 2.2μF or greater ceramic capacitor.
SMPS1 Low-Side Gate-Driver Output. DL1 swings from GND1 to V DD . DL1 is forced low in shutdown.
DL1 is also forced high when an output overvoltage fault is detected. DL1 is forced low in skip
mode after an inductor current zero crossing (GND1 - LX1) is detected.
Boost Flying Capacitor Connection for the DH1 High-Side Gate Driver. An internal switch between
V DD and BST1 charges the flying capacitor during the time the low-side FET is on.
SMPS1 Inductor Connection. LX1 is the internal lower supply rail for the DH1 high-side gate driver.
Also used as an input to SMPS1 ’s zero-crossing comparator.
SMPS1 High-Side Gate-Driver Output. DH1 swings from LX1 to BST1. Low in shutdown.
Open-Drain Output of Internal Comparator. VRHOT is pulled low when the voltage at THRM goes
below 1.5V (30% of V CC ). VRHOT is high impedance in shutdown.
Input of Internal Comparator. Connect the output of a resistor- and thermistor-divider (between V CC
and GND) to THRM. Select the components so the voltage at THRM falls below 1.5V (30% of V CC )
at the desired high temperature.
Controller Supply Voltage. Connect to a 4.5V to 5.5V source. Bypass to GND with 1μF minimum. A
V CC UVLO event that occurs while the IC is functioning is latched, and can only be cleared by
cycling V CC power or by toggling SHDN .
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ECC20DCMD | CONN EDGECARD 40POS .100 WW |
| TDL825K020S1B | CAP TANT 8.2UF 20V 10% RADIAL |
| 100R28-76B | CABLE FLAT FLEX 28POS 1MM 3" |
| EBM15DRTH | CONN EDGECARD 30POS DIP .156 SLD |
| TDL106K020S1C-F | CAP TANT 10UF 20V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080EVKIT+ | 功能描述:电源管理IC开发工具 MAX17080 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。