- 您现在的位置：买卖IC网 > PDF目录17272 > MAX17480EVKIT+ (Maxim Integrated Products)EVALUATION KIT FOR MAX17480 PDF资料下载
参数资料
| 型号： | MAX17480EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/48页 |
| 文件大小： | 0K |
| 描述： | EVALUATION KIT FOR MAX17480 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 3，非隔离 |
| 输入电压： | 4 ~ 26 V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX17480 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AMD 2-/3-Output Mobile Serial
VID Controller
V OUT3_PK TARGET3 LOAD3 +
= V
? 5 . 5 mV/A × (I
? I L 3
( V IN 3 ? V OUT 3 ) × V OUT 3
? I L 3 =
I FBAC = G m ( FBAC ) V CS
where V CS = V CSP - V CSN is the differential current-
sense voltage, and G m(FBAC) is 2.06mS (max) as
defined in the Electrical Characteristics table.
AC droop is required for stable operation of the
MAX17480. A minimum of 1.5mV/A is recommended.
AC droop must not be disabled.
Core Differential Remote Sense
The MAX17480 controller includes independent differen-
tial, remote-sense inputs for each CPU core to eliminate
the effects of voltage drops along the PCB traces and
through the processor’s power pins. The feedback-sense
(FBDC_) input connects to the remote-sensed output
through the resistance at FBDC_ (R FBDC_ ). The ground-
sense (GNDS_) input connects to an amplifier that adds
an offset directly to the target voltage, effectively
adjusting the output voltage to counteract the voltage
drop in the ground path. Connect the feedback-sense
(FBDC_) R FBDC_ resistor and ground-sense (GNDS_)
input directly to the respective CPU core ’s remote-
sense outputs as shown in Figure 2.
GNDS1 and GNDS2 are dual-function pins. At power-on,
the voltage levels on GNDS1 and GNDS2 configure the
MAX17480 as two independent switching SMPSs, or one
higher current 2-phase SMPS. Keep both GNDS1 and
GNDS2 low during power-up to configure the MAX17480
in separate mode. Connect GNDS1 or GNDS2 to a volt-
age above 0.8V (typ) for combined-mode operation. In
the AMD mobile system, this is automatically done by the
CPU that is plugged into the socket that pulls GNDS1 or
GNDS2 the V DDIO voltage level.
When GNDS1 is pulled high to indicate combined-
mode operation, the remote ground sense is automati-
cally switched to GNDS2. When GNDS2 is pulled high
to indicate combined-mode operation, the remote
ground sense is automatically switched to GNDS1.
GNDS1 and GNDS2 do not dynamically switch in the
real application. It is only switched when one CPU is
removed (e.g., split-core CPU), and another is plugged
in (e.g., combined-core CPU). This should not be done
when the socket is “hot” (i.e., powered).
The MAX17480 checks the GNDS1 and GNDS2 levels
at the time when the internal REFOK signal goes high,
and latches the operating mode information (separate
or combined mode). This latch is cleared by cycling the
SHDN pin.
Core Integrator Amplifier
An internal integrator amplifier forces the DC average of
the FBDC_ voltage to equal the target voltage. This
transconductance amplifier integrates the feedback
voltage and provides a fine adjustment to the regulation
voltage (Figure 4), allowing accurate DC output-voltage
regulation regardless of the output ripple voltage.
The MAX17480 disables the integrator during down-
ward VID transitions done in pulse-skipping mode. The
integrator remains disabled until the transition is com-
pleted (the internal target settles) and the output is in
regulation (edge detected on the error comparator).
The integrator amplifier can shift the output voltage by
± 80mV (min). The maximum difference between tran-
sient AC droop and DC droop should not exceed
± 80mV at the maximum allowed load current to guaran-
tee proper DC output-voltage accuracy over the full
load conditions.
NB SMPS Feedback Adjustment Amplifiers
NB Steady-State Voltage Positioning (DC Droop)
The NB SMPS has a built-in load-line that is -5.5mV/A.
The output peak voltage (V OUT3_PK+ ) is set to:
)
2
L 3 × V IN 3 × f SW 3
where the target voltage (V TARGET3 ) is defined in the
Nominal Output-Voltage Selection section, f SW3 is the
NB switching frequency, and I LOAD3 is the output load
current of the NB SMPS.
2-Wire Serial Interface (SVC, SVD)
The MAX17480 supports the 2-wire, write-only, serial-
interface bus as defined by the AMD serial VID inter-
face specification. The serial interface is similar to the
high-speed 3.4MHz I 2 C bus, but without the master
mode sequence. The bus consists of a clock line (SVC)
and a data line (SVD). The CPU is the bus master, and
the MAX17480 is the slave. The MAX17480 serial inter-
face works from 100kHz to 3.4MHz. In the AMD mobile
application, the bus runs at 3.4MHz.
The serial interface is active only after PGD_IN goes
high in the startup sequence. The CPU sets the VID
voltage of the three internal DACs and the PSI_L bit
through the serial interface.
During the startup sequence, the SVC and SVD inputs
serve an alternate function to set the 2-bit boot VID for
all three DACs while PWRGD is low.
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040A25IDCKRE4 | IC VREF SHUNT PREC 2.5V SC-70-5 |
| ECM25DCTN-S288 | CONN EDGECARD 50POS .156 EXTEND |
| RCC05DRTI-S13 | CONN EDGECARD 10POS .100 EXTEND |
| GBC31DCMH-S288 | CONN EDGECARD 62POS .100 EXTEND |
| RBC07DREN-S13 | CONN EDGECARD 14POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17480EVKIT+ | 功能描述:电源管理IC开发工具 MAX17480 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17480GTL+ | 功能描述:显示驱动器和控制器 2-/3-Output Mobile erial VID Ctlr RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX17480GTL+T | 功能描述:显示驱动器和控制器 2-/3-Output Mobile erial VID Ctlr RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX17482GTL+ | 功能描述:电压模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17482GTL+T | 功能描述:电压模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。