参数资料
型号: MAX1997ETJ+T
厂商: Maxim Integrated Products
文件页数: 26/31页
文件大小: 0K
描述: IC PWR SUPPLY TFT LCD 32TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
应用: 控制器,TFT LCD
输入电压: 2.7 V ~ 5.5 V
输出数: 5
输出电压: 2.7 V ~ 13 V
工作温度: 0°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 32-WFQFN 裸露焊盘
供应商设备封装: 32-TQFN-EP(5x5)
包装: 带卷 (TR)
Quintuple/Triple-Output TFT LCD Power Supplies
with Fault Protection and VCOM Buffer
I LOAD(MAX) = ? I DRV ? BE ? β MIN
Flying Capacitors
Increasing the flying capacitor (C X ) value increases the
output current capability. Increasing the capacitance
indefinitely has a negligible effect on output current
capability because the internal switch resistance and
the diode impedance limit the source impedance. A
0.1μF ceramic capacitor works well in most low-current
applications. The flying capacitor ’ s voltage rating must
exceed the following:
V CX > N ? V MAIN
where N is the stage number in which the flying capaci-
tor appears, and V MAIN is the main output voltage. For
example, the two-stage positive charge pump in the
typical application circuit (Figure 1) where V MAIN = 9V
contains two flying capacitors. The flying capacitor in
the first stage (C25) requires a voltage rating greater
than 9V. The flying capacitor in the second stage (C24)
requires a voltage rating greater than 18V.
Charge-Pump Output Capacitor
Increasing the output capacitance or decreasing the
ESR reduces the output ripple voltage and the peak-to-
peak transient voltage. With ceramic capacitors, the
output voltage ripple is dominated by the capacitance
value. Use the following equation to approximate the
required capacitor value:
Calculate R19 with the following equation:
R19 = R20 [(V G_ON / V FBP ) - 1]
where V FBP = 1.25V.
The output voltages of linear regulators REG 1 and
REG 2 can be similarly adjusted.
Adjust the negative linear-regulator (REG N) output
voltage by connecting a resistive voltage-divider from
V G_OFF to REF with the center tap connected to FBN
(Figure 1). Select R17 in the range of 10k ? to 30k ? .
Calculate R16 with the following equation:
R16 = R17 [(V FBN - V G_OFF ) / (V REF - V FBN )]
where V FBN = 125mV, V REF = 1.25V. REF can source
up to 75μA, using a resistor greater than 17k ? for R17
leaves at least 10μA for other uses.
Pass Transistor Selection
The pass transistor must meet specifications for current
gain ( β ), input capacitance, collector-emitter saturation
voltage, and power dissipation. The transistor ’ s current
gain limits the guaranteed maximum output current to:
? V ?
? R BE ?
C OUT ≥
I LOAD
2f OSC V RIPPLE
where I DRV is the minimum guaranteed base drive cur-
rent, V BE is the base-to-emitter voltage of the transistor,
and R BE is the pullup resistor connected between the
where V RIPPLE is the peak-to-peak value of the output
ripple.
Charge-Pump Rectifier Diodes
Use Schottky diodes with a current rating equal to or
greater than two times the average charge-pump input
current. If the loaded charge-pump output voltage is
greater than required, some or all of the Schottky
diodes can be replaced with low-cost silicon switching
diodes with an equivalent current rating. The charge-
pump input current is:
I CP _ IN = I CP _ OUT ? N
where N is the number of charge-pump stages.
Linear-Regulator Controllers
Output Voltage Selection
Adjust the positive linear-regulator (REG P) output volt-
age by connecting a resistive voltage-divider from
V G_ON to GND with the center tap connected to FBP
(Figure 1). Select R20 in the range of 10k ? to 30k ? .
transistor ’ s base and emitter. Furthermore, the transis-
tor ’ s current gain increases the linear regulator ’ s DC
loop gain (see the Stability Requirements section), so
excessive gain destabilizes the output. Therefore, tran-
sistors with current gain over 100 at the maximum out-
put current can be difficult to stabilize and are not
recommended. The transistor ’ s input capacitance and
input resistance also create a second pole, which
could be low enough to make the output unstable when
heavily loaded.
The transistor ’ s saturation voltage at the maximum out-
put current determines the minimum input-to-output
voltage differential that the linear regulator supports.
Alternatively, the package ’ s power dissipation could
limit the usable maximum input-to-output voltage differ-
ential. The maximum power dissipation capability of the
transistor ’ s package and mounting must exceed the
actual power dissipation in the device. The power dissi-
pation equals the maximum load current times the max-
imum input-to-output voltage differential:
P = I LOAD(MAX) (V LDOIN - V LDOOUT ) = I LOAD(MAX) V CE
26
______________________________________________________________________________________
相关PDF资料
PDF描述
MAX256ASA+T IC DRVR H-BRIDGE 8-SOIC
MAX3273ETG+T IC LASR DRVR 2.7GBPS 3.6V 24TQFN
MAX3296CTI+T IC LASR DRVR 2.5GBPS 5.5V 28TQFN
MAX3353EEUE+T IC CHARGE PUMP USB OTG 16TSSOP
MAX3355EEUD+T IC CHARGE PUMP USB OTG 14TSSOP
相关代理商/技术参数
参数描述
MAX1997EVKIT 制造商:Maxim Integrated Products 功能描述:QUINTUPLE/TRIPLE OUTPUT TFT LCD POWER SUPPLIE - Bulk
MAX19983A 功能描述:上下转换器 RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19985AETX+ 功能描述:上下转换器 High-Gain 700MHz to 1GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19985AETX+T 功能描述:上下转换器 High-Gain 700MHz to 1GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
MAX19985ETX+ 功能描述:上下转换器 Dual, SiGe, .7-1GHz Downconversion Mixer RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128