参数资料
| 型号： | MAX3140EEI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | IC UART W/RS485 28-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 特点： | 收发器 |
| FIFO's： | 8 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-QSOP |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX3140
SPI/MICROWIRE-Compatible UART with Integrated
True Fail-Safe RS-485/RS-422 Transceivers
24
______________________________________________________________________________________
Example 2: Setting up only the data-available (or data-
being-read) interrupt.
Send the 16-bit word below into DIN of the MAX3140
using the WRITE CONFIGURATION register. This 16-bit
word configures the MAX3140 for 9600bps, 8-bit
words, no parity, and one stop bit with a 1.8432MHz
crystal.
binary 1100010000001010
HEX
C40A
Receive FIFO
The MAX3140 contains a receive FIFO for data received
by the UART to minimize processor overhead. The
receive FIFO is 8 words deep and clears automatically if
it overflows. Shutting down the UART also clears the
receive FIFO. Upon power-up, the receive FIFO is
enabled. To disable the receive FIFO, set the FEN bit
high when writing to the WRITE CONFIGURATION regis-
ter. To check whether the FIFO is enabled or disabled,
read back the FEN bit using the READ CONFIGURA-
TION.
UART Shutdown
In shutdown, the oscillator turns off to reduce power
consumption (ICCSHDN UART < 1mA). The UART enters
shutdown in one of two ways: by a software command
(SHDNi bit = 1) or by a hardware command (SHDN =
logic low). The hardware shutdown immediately termi-
nates any transmission in progress. The software shut-
down, requested by setting SHDNi bit = 1, is entered
upon completing the transmission of the data in both
the transmit-shift register and the transmit-buffer regis-
ter. The SHDNo bit is set when the UART enters shut-
down (either hardware or software). The microcontroller
(C) can monitor the SHDNo bit to determine when all
data has been transmitted, then shut down RS-485
transceivers at that time.
Shutdown clears the receive FIFO, R, RA/FE, D0r–D7r,
Pr, and Pt registers and sets the T bit high.
Configuration bits (RM, TM, PM, RAM, IR, ST, PE, L, B0-
3, and RTS) can be modified when SHDNo = 1 and
CTS can also be read. Even though RA is reset upon
entering shutdown, it goes high when a transition is
detected on the RX pin. This allows the UART to moni-
tor activity on the receiver when in shutdown.
The command to power up (SHDNi = 0) turns on the
oscillator when CS goes high if SHDN = logic high, with
a start-up time of at least 25ms. This is done by writing
to the WRITE CONFIGURATION register, which clears
all registers but RTS and CTS. Since the crystal oscilla-
tor typically requires at least 25ms to start, the first
received characters can be garbled and a framing
error may occur.
RS-485/RS-422 Transceiver
The RS-485/RS-422 transceiver is equipped with
numerous features allowing it to be configured for any
RS-485/RS-422 application. Figure 10 shows the
MAX3140 functional diagram. Included in the RS-
485/RS-422 transceiver function is full- and half-duplex
selectability, true fail-safe circuitry, programmable
slew-rate limiting, receiver input filtering, and phase
control circuitry.
Full Duplex or Half Duplex
The MAX3140 operates in either full- or half-duplex
mode. Drive the H/F pin low, leave it unconnected
(internal pull-down), or connect it to GND for full-duplex
operation or drive it high for half-duplex operation. In
half-duplex mode, the receiver inputs are switched to
the driver outputs, connecting outputs Y and Z to inputs
A and B, respectively. In half-duplex mode, the internal
full-duplex receiver input resistors are still connected to
inputs A and B.
True Fail-Safe Circuitry
The MAX3140 guarantees a logic-high receiver output
when the receiver inputs are shorted or open, or when
they are connected to a terminated transmission line
with all drivers disabled. This is done by setting the
receiver threshold between -50mV and -200mV. If the
differential receiver input voltage (A-B) is greater than
or equal to -50mV, RO is logic high. If A-B is less than
or equal to -200mV, RO is logic low. In the case of a
terminated bus with all transmitters disabled, the
receiver’s differential input voltage is pulled to 0 by the
termination. With the receiver thresholds of the
MAX3140, this results in a logic high with a 50mV mini-
mum noise margin. Unlike previous fail-safe devices,
the -50mV to -200mV threshold complies with the
±200mV EIA/TIA-485 standard.
Programmable Slew-Rate Limiting
The MAX3140 has several programmable operating
modes. Transmitter rise and fall times are programma-
ble at 2500ns, 750ns, or 25ns, resulting in maximum
data rates of 115kbps, 500kbps, or 10Mbps, respec-
tively. To select the desired data rate, drive SRL to one
of three possible states by using a three-state driver, by
connecting it to VCC or GND, or by leaving it uncon-
nected. For 115kbps operation, set the three-state
device in high-impedance mode or leave SRL uncon-
nected. For 500kbps operation, drive SRL high or con-
nect it to VCC. For 10Mbps operation, drive SRL low or
connect it to GND. SRL can be changed during opera-
tion without interrupting data communications.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3157CAI | IC TXRX RS485/422 250KBPS 28SSOP |
| MAX3160CAP | IC TXRX RS485/422 10MBPS 20SSOP |
| MAX3160EEAP+T | IC TXRX RS232/485/422 20SSOP |
| MAX3170CAI | IC TXRX CLOCK/DATA 3.3V 28-SSOP |
| MAX3171CAI | IC TXRX MULTIPROTOCL 3.3V 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3140EEI+ | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3140EEI+T | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3140EEI-T | 功能描述:UART 接口集成电路 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3147NC SPL | 制造商:Toshiba America Electronic Components 功能描述:NORTEL HDD - Bulk |
| MAX314C/D | 功能描述:模拟开关 IC 10Ohm Quad SPST CMOS Analog Switches RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。