参数资料
| 型号： | MAX3140EEI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/36页 |
| 文件大小： | 0K |
| 描述： | IC UART W/RS485 28-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 特点： | 收发器 |
| FIFO's： | 8 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-QSOP |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX3140
SPI/MICROWIRE-Compatible UART with Integrated
True Fail-Safe RS-485/RS-422 Transceivers
______________________________________________________________________________________
25
Receiver Input Filtering
The receivers of the MAX3140, when operating in
115kbps or 500kbps mode, incorporate input filtering in
addition to input hysteresis. This filtering enhances
noise immunity with differential signals that have very
slow rise and fall times. Receiver propagation delay
increases by 20% due to this filtering.
Phase Control Circuitry
Occasionally, twisted-pair lines are connected back-
ward from normal orientation. The MAX3140 has two
pins that invert the phase of the driver and the receiver
to correct for this problem. For normal operation, drive
TXP and RXP low, connect them to ground, or leave
them unconnected (internal pull-down). To invert the
driver phase, drive TXP high or connect it to VCC. To
invert the receiver phase, drive RXP high or connect it
to VCC. Note that the receiver threshold is positive
when RXP is high.
Applications Information
Crystals, Oscillators, and
Ceramic Resonators
The MAX3140 includes an oscillator circuit derived
from an external crystal for baud-rate generation. For
standard baud rates, use a 1.8432MHz or 3.6864MHz
crystal. The 1.8432MHz crystal results in lower operat-
ing current; however, the 3.6864MHz crystal may be
more readily available in surface-mount packages.
Ceramic resonators are low-cost alternatives to crystals
and operate similarly, though the Q and accuracy are
lower. Some ceramic resonators are available with inte-
gral load capacitors, which can further reduce cost.
The trade-off between crystals and ceramic resonators
is in initial frequency accuracy and temperature drift.
Keep the total error in the baud-rate generator below
1% for reliable operation with other systems. This is
accomplished easily with a crystal, and in most cases
is achieved with ceramic resonators. Table 8 lists differ-
ent types of crystals and resonators and their suppliers.
The MAX3140’s oscillator supports parallel-resonant
mode crystals and ceramic resonators, or can be driven
from an external clock source. Internally, the oscillator
consists of an inverting amplifier with its input (X1) tied
to its output (X2) by a bias network that self-biases the
inverter at approximately VCC/2. The external feedback
circuit, usually a crystal from X2 to X1, provides 180° of
phase shift, causing the circuit to oscillate. As shown in
the standard application circuit, the crystal or resonator
is connected between X1 and X2, with the load capaci-
tance for the crystal being the series combination of C1
and C2. For example, for a 1.8432MHz crystal with a
specified load capacitance of 11pF, use 22pF capaci-
tors on either side of the crystal to ground. Series-res-
onant mode crystals have a slight frequency error,
typically oscillating 0.03% higher than specified series-
resonant frequency when operated in parallel mode.
Note: It is very important to keep crystal, resonator,
and load-capacitor leads and traces as short and
direct as possible. Make the X1 and X2 trace lengths
and ground tracks short, with no intervening traces.
This helps minimize parasitic capacitance and noise
pickup in the oscillator, and reduces EMI. Minimize
capacitive loading on X2 to minimize supply current.
The MAX3140’s X1 input can be driven directly by an
external CMOS clock source. The trip level is approxi-
mately equal to VCC/2. Make no connection to X2 in this
mode. If a TTL or non-CMOS clock source is used, AC-
couple with a 10nF capacitor to X1. A 2V peak-to-peak
swing on the input is required for reliable operation.
Table 8. Component and Supplier List
Murata North America
ECS International, Inc.
SUPPLIER
CSA1.84MG
ECS-18-13-1
PART
NUMBER
(800) 831-9172
(913) 782-7787
PHONE
NUMBER
DESCRIPTION
1.8432
Through-Hole
Ceramic Resonator
1.8432
Through-Hole Crystal
(HC-49/U)
FREQUENCY
(MHz)
47
25
TYPICAL
C1, C2 (pF)
ECS International, Inc.
ECS-36-20-5P
ECS-36-18-4
(913) 782-7787
3.6864
SMT Crystal
3.6864
Through-Hole Crystal
(HC-49/US)
39
33
AVX/Kyocera
PBRC-3.68B
(803) 448-9411
3.6864
SMT Ceramic
Resonator
None
(integral)
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3157CAI | IC TXRX RS485/422 250KBPS 28SSOP |
| MAX3160CAP | IC TXRX RS485/422 10MBPS 20SSOP |
| MAX3160EEAP+T | IC TXRX RS232/485/422 20SSOP |
| MAX3170CAI | IC TXRX CLOCK/DATA 3.3V 28-SSOP |
| MAX3171CAI | IC TXRX MULTIPROTOCL 3.3V 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3140EEI+ | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3140EEI+T | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3140EEI-T | 功能描述:UART 接口集成电路 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3147NC SPL | 制造商:Toshiba America Electronic Components 功能描述:NORTEL HDD - Bulk |
| MAX314C/D | 功能描述:模拟开关 IC 10Ohm Quad SPST CMOS Analog Switches RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。