- 您现在的位置：买卖IC网 > PDF目录229280 > MAX6874ETJ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors PDF资料下载
参数资料
| 型号： | MAX6874ETJ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors |
| 中文描述： | 6-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC32 |
| 封装： | 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-32 |
| 文件页数： | 22/40页 |
| 文件大小： | 337K |
| 代理商： | MAX6874ETJ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MAX6874/MAX6875
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
______________________________________________________________________________________
29
Block Write
The block write protocol allows the master device to
write a block of data (1 to 16 bytes) to the EEPROM or
to the register bank (see Figure 7). The destination
address must already be set by the send byte or write
byte protocol and the command code must be 83h. If
the number of bytes to be written causes the address
pointer to exceed 45h for the configuration register or
configuration EEPROM, the address pointer stays at
45h, overwriting this memory address with the remain-
ing bytes of data. The last data byte sent is stored at
register address 45h. If the number of bytes to be writ-
ten exceeds the address pointer FFh for the user EEP-
ROM, the address pointer loops back to 00h, and
continues writing bytes until all data is written. The
block write procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends the 8-bit command code for
block write (83h).
5) The addressed slave asserts an ACK on SDA.
6) The master sends the 8-bit byte count (1 to 16 bytes) N.
7) The addressed slave asserts an ACK on SDA.
8) The master sends 8 bits of data.
9) The addressed slave asserts an ACK on SDA.
10) Repeat steps 8 and 9 one time.
11) The master generates a stop condition.
Receive Byte
The receive byte protocol allows the master device to
read the register content of the MAX6874/MAX6875
(see Figure 7). The EEPROM or register address must
be preset with a send byte or write word protocol first.
Once the read is complete, the internal pointer increas-
es by one. Repeating the receive byte protocol reads
the contents of the next address. The receive byte pro-
cedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
read bit (high).
3) The addressed slave asserts an ACK on SDA.
4) The slave sends 8 data bits.
5) The master asserts a NACK on SDA.
6) The master generates a stop condition.
Block Read
The block read protocol allows the master device to
read a block of 16 bytes from the EEPROM or register
bank (see Figure 7). Read fewer than 16 bytes of data
by issuing an early STOP condition from the master, or
by generating a NACK with the master. The send byte
or write byte protocol predetermines the destination
address with a command code of 84h. The block read
procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends 8 bits of the block read command
(84h).
5) The slave asserts an ACK on SDA, unless busy.
6) The master generates a repeated start condition.
7) The master sends the 7-bit slave address and a
read bit (high).
8) The slave asserts an ACK on SDA.
9) The slave sends the 8-bit byte count (16).
10) The master asserts an ACK on SDA.
11) The slave sends 8 bits of data.
12) The master asserts an ACK on SDA.
13) Repeat steps 8 and 9 fifteen times.
14) The master generates a stop condition.
Address Pointers
Use the send byte protocol to set the register address
pointers before read and write operations. For the con-
figuration registers, valid address pointers range from
00h to 45h. Register addresses outside of this range
result in a NACK being issued from the MAX6874/
MAX6875. When using the block write protocol, the
address pointer automatically increments after each
data byte, except when the address pointer is already
at 45h. If the address pointer is already 45h, and more
data bytes are being sent, these subsequent bytes
overwrite address 45h repeatedly, leaving only the last
data byte sent stored at this register address.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6876ETX | EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit |
| MAX6884ETP | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6884ETP-T | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6885ETP | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6887AETE | Hex/Quad, Power-Supply Supervisory Circuits |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX6875ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。