- 您现在的位置：买卖IC网 > PDF目录229280 > MAX6874ETJ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors PDF资料下载
参数资料
| 型号： | MAX6874ETJ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors |
| 中文描述： | 6-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC32 |
| 封装： | 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-32 |
| 文件页数： | 4/40页 |
| 文件大小： | 337K |
| 代理商： | MAX6874ETJ |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MAX6874/MAX6875
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
12
______________________________________________________________________________________
Powering the MAX6874/MAX6875
The MAX6874/MAX6875 derive power from the positive
voltage-detector inputs: IN1 or IN3–IN5. A virtual diode-
ORing scheme selects the positive input that supplies
power to the device (see the Functional Diagram). IN1
must be at least +4V or one of IN3–IN5 (MAX6874)/
IN3–IN4 (MAX6875) must be at least +2.7V to ensure
device operation. An internal LDO regulates IN1 down
to +5.4V.
The highest input voltage on IN3–IN5 (MAX6874)/
IN3–IN4 (MAX6875) supplies power to the device, unless
VIN1 ≥ +6.5V, in which case IN1 supplies power to the
device. For +4V < VIN1 < +6.5V and one of VIN3 through
VIN5 > +2.7V, the input power source cannot be deter-
mined due to the dropout voltage of the LDO. Internal
hysteresis ensures that the supply input that initially pow-
ered the device continues to power the device when
multiple input voltages are within 50mV of each other.
ABP powers the analog circuitry; bypass ABP to GND
with a 1F ceramic capacitor installed as close to the
device as possible. The internal supply voltage, mea-
sured at ABP, equals the maximum of IN3–IN5
(MAX6874)/IN3–IN4 (MAX6875) if VIN1 = 0, or equals
+5.4V when VIN1 > +6.5V. Do not use ABP to provide
power to external circuitry.
The MAX6874/MAX6875 also generate a digital supply
voltage (DBP) for the internal logic circuitry and the
EEPROM; bypass DBP to GND with a 1F ceramic
capacitor installed as close to the device as possible.
The nominal DBP output voltage is +2.55V. Do not use
DBP to provide power to external circuitry.
Inputs
The MAX6874/MAX6875 contain multiple logic and volt-
age-detector inputs. Table 1 summarizes these various
inputs.
Set the threshold voltages for each voltage-detector
input with registers 00h–05h. Each threshold voltage is
an undervoltage threshold. Set the threshold range for
each voltage detector with register 0Dh.
Table 1. Programmable Features
FEATURE
DESCRIPTION
High-Voltage Input
(IN1)
Undervoltage threshold
+2.5V to +13.2V threshold in 50mV increments
+1.25V to +7.625V threshold in 25mV increments
Voltage Input (IN2)
Undervoltage threshold
+2.5V to +5.5V threshold in 50mV increments
+1.25V to +3.05V threshold in 25mV increments
Voltage Input
IN3–IN6 (MAX6874),
IN3–IN4 (MAX6875)
Undervoltage threshold
+1V to +5.5V threshold in 20mV increments
+0.5V to +3.05V threshold in 10mV increments
Programmable Outputs
PO1–PO8 (MAX6874),
PO1–PO5 (MAX6875)
Active high or active low
Open-drain output
Dependent on MR, MARGIN, IN_, GPI1–GPI4 , WD, and/or PO_
Programmable timeout periods of 25s, 1.5625ms, 6.25ms, 25ms, 50ms, 200ms, 400ms, or 1.6s
General-Purpose
Logic Inputs,
GPI1–GPI4 (MAX6874),
GPI1–GPI3 (MAX6875)
Active-high or active-low logic levels
Configure GPI_ as inputs to watchdog timers or programmable output stages
Watchdog Timer
Clear dependent on any combination of one GPI_ input and one programmable output, a GPI_ input
only, or a programmable output only
Initial watchdog timeout period of 6.25ms, 25ms, 100ms, 400ms, 1.6s, 6.4s, 25.6s, or 102.4s
Normal watchdog timeout period of 6.25ms, 25ms, 100ms, 400ms, 1.6s, 6.4s, 25.6s, or 102.4s
Watchdog enable/disable
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6876ETX | EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit |
| MAX6884ETP | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6884ETP-T | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6885ETP | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6887AETE | Hex/Quad, Power-Supply Supervisory Circuits |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX6875ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。