- 您现在的位置：买卖IC网 > PDF目录229280 > MAX6874ETJ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors PDF资料下载
参数资料
| 型号： | MAX6874ETJ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | EEPROM-Programmable, Hex/Quad, Power-Supply Sequencers/Supervisors |
| 中文描述： | 6-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC32 |
| 封装： | 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-32 |
| 文件页数： | 30/40页 |
| 文件大小： | 337K |
| 代理商： | MAX6874ETJ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MAX6874/MAX6875
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
36
______________________________________________________________________________________
4) Any attempt to communicate with the device prior to
this download completion results in a NACK being
issued from the MAX6874/MAX6875.
Forcing Programmable
Outputs High During Power-Up
A weak 10A pulldown holds all programmable outputs
low during power-up until ABP exceeds the undervolt-
age lockout (UVLO) threshold. Applications requiring a
guaranteed high programmable output for ABP down to
GND require external pullup resistors to maintain the
logic state until ABP exceeds UVLO. Use 20k resis-
tors for most applications.
Uses for General-Purpose
Inputs (GPI1–GPI4)
Watchdog Timer
Program GPI_ as an input to the watchdog timer in the
MAX6874/MAX6875. The GPI_ input must toggle within
the watchdog timeout period, otherwise any program-
mable output dependent on the watchdog timer
asserts.
Additional Manual Reset Functions
Program PO7 (MAX6874)/PO5 (MAX6875) to depend
on one of the GPI_ inputs. Any output that depends on
GPI_ asserts when GPI_ is held in its active state, effec-
tively acting as a manual reset input.
Other Fault Signals from C
Connect a general-purpose output from a C to one of
the GPI_ inputs to allow interrupts to assert any output
of the MAX6874/MAX6875. Configure one of the pro-
grammable outputs to assert on whichever GPI_ input
connects to the general purpose output of the C.
Layout and Bypassing
For better noise immunity, bypass each of the voltage
detector inputs to GND with 0.1F capacitors installed
as close to the device as possible. Bypass ABP and
DBP to GND with 1F capacitors installed as close to
the device as possible. ABP and DBP are internally
generated voltages and should not be used to supply
power to external circuitry.
Configuration Latency Period
A delay of less than 5s occurs between writing to the
configuration registers and the time when these
changes actually take place, except when changing
one of the voltage-detector thresholds. Changing a
voltage-detector threshold typically takes 150s. When
changing EEPROM contents, a software reboot or
cycling of power is required for these changes to trans-
fer to volatile memory.
Chip Information
PROCESS: BiCMOS
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6876ETX | EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit |
| MAX6884ETP | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6884ETP-T | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6885ETP | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6887AETE | Hex/Quad, Power-Supply Supervisory Circuits |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX6875ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。