参数资料
| 型号： | MAX769EEI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC PAGER SYSTEM 28-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | 手持/移动设备 |
| 电流 - 电源： | 4µA |
| 电源电压： | 1.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-QSOP |
| 供应商设备封装： | 28-QSOP |
| 包装： | 管件 |
2 or 3-Cell, Step-Up/Down,
Two-Way Pager System IC
Serial data is clocked in and out MSB first. Input data is
latched on the CLK rising edge, and output data is
shifted out on the CLK falling edge. When CS goes low,
DO immediately contains the MSB output bit (D7). D6 is
not clocked out until the falling clock edge that follows
the first rising clock edge after a Chip Select. See the
timing diagrams in Figures 4 and 5.
SPI writes and reads concurrently, so it may be neces-
sary to perform dummy writes in order to read output
data. Four output data bits (D7–D4, Table 4) are sent
from SDO each time a serial operation occurs.
CS
???
When R2 = 0, R0 and R1 are address pointers.
However, when R2 = 1, the 7 remaining bits (R1, R0
and D4–D0) become DAC programming bits. This vio-
lation of programming etiquette (R1 and R0 are some-
times address bits and other times data bits) allows the
CH DAC to be loaded with only one write operation.
Writing all zeros to the CH DAC turns it, the CH0, CH1,
and CH2 comparators, and the NICD and BATT volt-
age-sensing resistors off to minimize current consump-
tion. This reduces current drain from OUT by about
30μA.
t CSH
t CSS
t CL
t CH
t CSH
SCLK
DIN
t DS
t DH
???
???
t DV
DOUT
Figure 4. Detailed Serial-Interface Timing
CS
SCL
???
t DO
t TR
SCO
SDI
D7
R2
D6
R1
D5
R0
D4
D4
0
D3
0
D2
0
D1
0
D0
Figure 5. CS , SCL, SDO, and SDI Serial Timing
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7705EPA+ | IC MPU SUPPLY MON 8-DIP |
| MAX771ESA+T | IC REG CTRLR BST PWM 8-SOIC |
| MAX774ESA+ | IC REG CTRLR INV PWM 8-SOIC |
| MAX791CSE | IC MPU SUPERVISOR CIRCUIT 16SOIC |
| MAX792MCPE | IC MPU SUPRVSRY CIRC 4.37V 16DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX769EEI+ | 功能描述:PMIC 解决方案 2-3 Cell Step-Up/Dwn 2-Way Pgr System IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX769EEI+T | 功能描述:PMIC 解决方案 2-3 Cell Step-Up/Dwn 2-Way Pgr System IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX769EEI-T | 功能描述:PMIC 解决方案 2-3 Cell Step-Up/Dwn 2-Way Pgr System IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX769EVKIT | 功能描述:电源管理IC开发工具 Evaluation Kit for the MAX769 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX7705CPA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。