参数资料
| 型号： | MAX8756ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/30页 |
| 文件大小： | 0K |
| 描述： | IC CNTRL DUAL PS 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 4 V ~ 26 V |
| 输出数： | 2 |
| 输出电压： | 1.5V，1.8V，1 V ~ 2.3 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Interleaved High-Efficiency, Dual Power-Supply
Controllers for Notebook Computers
Output Undervoltage Protection
If the output voltage of either SMPS falls below 70% of
its regulation voltage, the corresponding controller sets
its undervoltage fault latch, pulls PGOOD_ low, and
begins soft-shutdown for the corresponding SMPS con-
troller by pulsing DL_. DH_ remains off during the soft-
shutdown sequence initiated by an unvervoltage fault.
The other controller is not affected. After soft-shutdown
has completed, the MAX8716/MAX8717/MAX8756/
MAX8757 force DL_ high and DH_ low. Cycle V CC
below 1V or toggle ON_ to clear the undervoltage fault
latch and restart the SMPS controller.
V CC POR and UVLO
Power-on reset (POR) occurs when V CC rises above
approximately 2V, resetting the fault latch and prepar-
ing the PWM for operation. V CC undervoltage-lockout
(UVLO) circuitry inhibits switching, forces PGOOD_
low, and forces the DL_ gate drivers low.
?
?
?
Maximum Load Current. There are two values to
consider. The peak load current (I LOAD(MAX) ) deter-
mines the instantaneous component stresses and fil-
tering requirements and thus drives output capacitor
selection, inductor saturation rating, and the design
of the current-limit circuit. The continuous load cur-
rent (I LOAD ) determines the thermal stresses and thus
drives the selection of input capacitors, MOSFETs,
and other critical heat-contributing components.
Switching Frequency. This choice determines the
basic trade-off between size and efficiency. The
optimal frequency is largely a function of maximum
input voltage, due to MOSFET switching losses that
are proportional to frequency and V IN 2 . The opti-
mum frequency is also a moving target, due to rapid
improvements in MOSFET technology that are mak-
ing higher frequencies more practical.
Inductor Operating Point. This choice provides
If V CC drops low enough to trip the UVLO comparator
while ON_ is high, the MAX8716/MAX8717/MAX8756/
MAX8757 immediately force DH_ and DL_ low on both
controllers. The output discharges to 0V at a rate
dependent on the load and the total output capaci-
tance. This prevents negative output voltages, eliminat-
ing the need for a Schottky diode to GND at the output.
Thermal Fault Protection
The MAX8716/MAX8717/MAX8756/MAX8757 feature a
thermal fault-protection circuit. When the junction tem-
perature rises above +160°C, a thermal sensor sets the
fault latches, pulls PGOOD low, and shuts down both
SMPS controllers using the soft-shutdown sequence
(see the Sort-Start and Soft-Shutdown section). Cycle
V CC below 1V or toggle ON1 and ON2 to clear the fault
latches and restart the controllers after the junction
temperature cools by 15°C.
trade-offs between size vs. efficiency and transient
response vs. output ripple. Low inductor values pro-
vide better transient response and smaller physical
size, but also result in lower efficiency and higher
output ripple due to increased ripple currents. The
minimum practical inductor value is one that causes
the circuit to operate at the edge of critical conduc-
tion (where the inductor current just touches zero
with every cycle at maximum load). Inductor values
lower than this grant no further size-reduction bene-
fit. The optimum operating point is usually found
between 20% and 50% ripple current. When pulse-
skipping ( SKIP low and light loads), the inductor
value also determines the load-current value at
which PFM/PWM switchover occurs.
Inductor Selection
The switching frequency and inductor operating point
determine the inductor value as follows:
Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency
and inductor operating point (ripple-current ratio). The
L =
V OUT ( V IN ? V OUT )
V IN ? OSC I LOAD ( MAX ) LIR
primary design trade-off lies in choosing a good switch-
ing frequency and inductor operating point, and the fol-
lowing four factors dictate the rest of the design:
For example: I LOAD(MAX) = 5A, V IN = 12V, V OUT = 5V,
f OSC = 300kHz, 30% ripple current or LIR = 0.3:
?
Input Voltage Range. The maximum value (V IN(MAX) )
must accommodate the worst-case, high AC-adapter
L =
5 V × ( 12 V ? 5 V )
12 V × 300 kHz × 5 A × 0 . 3
= 6 . 50 μ H
voltage. The minimum value (V IN(MIN) ) must account
for the lowest battery voltage after drops due to con-
nectors, fuses, and battery selector switches. If there
is a choice at all, lower input voltages result in better
efficiency.
Find a low-loss inductor having the lowest possible DC
resistance that fits in the allotted dimensions. Most
inductor manufacturers provide inductors in standard
values, such as 1.0μH, 1.5μH, 2.2μH, 3.3μH, etc. Also
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8758ETG+T | IC REG STEP UP 24-TQFN |
| MAX8759ETI+T | IC CNTRL CCFL BACKLIGHT 28TQFN |
| MAX8760ETL+T | IC CNTRLR QUICK PWM 40-TQFN |
| MAX8761ETG+T | IC REG LINEAR LCD 24-TQFN |
| MAX8764ETP+T | IC CNTRL STP DWN HS 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8757ETG+ | 制造商:Maxim Integrated Products 功能描述:INTERLEAVED HI-EFF AND DUAL PS CNTRLR 24TQFN EP - Rail/Tube |
| MAX8757ETI+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8758ETG+ | 功能描述:LCD 驱动器 Step-Up Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8758ETG+T | 功能描述:LCD 驱动器 Step-Up Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX8758ETJ | 功能描述:LCD 驱动器 Step-Up Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。