- 您现在的位置：买卖IC网 > PDF目录13115 > MAX8760ETL+ (Maxim Integrated Products)IC CNTRLR QUICK PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX8760ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/39页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR QUICK PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，6 位 VID AMD 移动式 Turion? |
| 输入电压： | 4 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 0.38 V ~ 1.55 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Dual-Phase, Quick-PWM Controller for AMD
Mobile Turion 64 CPU Core Power Supplies
I MAIN - I 2 ND = I MAIN ? 1 - ? MAIN ? ?
Current Balance
Without active current-balance circuitry, the current
matching between phases depends on the MOSFET’s
on-resistance (R DS(ON) ), thermal ballasting, on-/off-time
matching, and inductance matching. For example, vari-
ation in the low-side MOSFET on-resistance (ignoring
thermal effects) results in a current mismatch that is
proportional to the on-resistance difference:
? ? R ? ?
? ? ? R 2 ND ? ? ?
However, mismatches between on-times, off-times, and
inductor values increase the worst-case current imbal-
ance, making it impossible to passively guarantee
accurate current balancing.
The multiphase Quick-PWM controller integrates the dif-
ference between the current-sense voltages and
adjusts the on-time of the secondary phase to maintain
current balance. The current balance now relies on the
accuracy of the current-sense resistors instead of the
inaccurate, thermally sensitive on-resistance of the low-
side MOSFETs.
With active current balancing, the current mismatch is
determined by the current-sense resistor values and the
offset voltage of the transconductance amplifiers:
The inverting (OAIN-) and noninverting (OAIN+) inputs
are used to differentially sense the voltage across the
voltage-positioning sense resistor. The op amp’s output is
internally connected to the regulator’s feedback input
(FB). The op amp should be configured as a noninvert-
ing, differential amplifier, as shown in Figure 10. The
voltage-positioning slope is set by properly selecting the
feedback resistor connected from FB to OAIN- (see the
Setting Voltage Positioning section). For applications
using a slave controller, additional differential input
resistors (summing configuration) can be connected to
the slave’s voltage-positioning sense resistor. Summing
together both the master and slave current-sense signals
ensures that the voltage-positioning slope remains con-
stant when the slave controller is disabled.
The controller also uses the amplifier for remote output
sensing (FBS) by summing in the remote-sense voltage
into the positive terminal of the voltage-positioning
amplifier (Figure 10).
In applications that do not require voltage-positioning
gain, the amplifier can be disabled by connecting the
OAIN- pin directly to V CC . The disabled amplifier’s out-
put becomes high impedance, guaranteeing that the
unused amplifier does not corrupt the FB input signal.
The logic threshold to disable the op amp is approxi-
mately V CC - 1V.
I OS ( IBAL ) = I LM - I LS =
V OS ( IBAL )
R SENSE
Integrator Amplifier
A feedback amplifier forces the DC average of the
feedback voltage to equal the VID DAC setting. This
where V OS(IBAL) is the current balance offset specifica-
tion in the Electrical Characteristics table.
The worst-case current mismatch occurs immediately
after a load transient due to inductor value mismatches,
resulting in different di/dt for the two phases. The time it
takes the current-balance loop to correct the transient
imbalance depends on the mismatch between the
inductor values and switching frequency.
Feedback Adjustment Amplifiers
Voltage-Positioning Amplifier
The multiphase Quick-PWM controllers include an inde-
pendent operational amplifier for adding gain to the volt-
age-positioning sense path. The voltage-positioning gain
allows the use of low-value current-sense resistors to
minimize power dissipation. This 3MHz gain-bandwidth
amplifier was designed with low offset voltage (70μV typ)
to meet the IMVP output-accuracy requirements.
transconductance amplifier integrates the feedback
voltage and provides a fine adjustment to the regulation
voltage (Figure 5), allowing accurate DC output voltage
regulation regardless of the output ripple voltage. The
feedback amplifier has the ability to shift the output
voltage. The differential input voltage range is at least
±80mV total, including DC offset and AC ripple. The
integration time constant can be set easily with an
external compensation capacitor at the CCV pin. Use a
capacitor value of 47pF to 1000pF (150pF typ).
Differential Remote Sense
The multiphase Quick-PWM controllers include differen-
tial remote-sense inputs to eliminate the effects of volt-
age drops down the PC board traces and through the
processor’s power pins. The remote output sense (FBS)
is accomplished by summing in the remote-sense volt-
age into the positive terminal of the voltage-positioning
amplifier (Figure 10). The controller includes a dedicat-
ed input and internal amplifier for the remote ground
sense. The GNDS amplifier adds an offset directly to
the feedback voltage, adjusting the output voltage to
counteract the voltage drop in the ground path.
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| RCB40DHLN | CONN EDGECARD 80POS DIP .050 SLD |
| MAX17528GTJ+ | IC PWM CTRLR STP-DWN 32TQFN-EP |
| RYM12DRST-S664 | CONN EDGECARD 24POS DIP .156 SLD |
| MAX17036GTL+ | IC CTRLR VID QUICK-PWM 40-TQFN |
| VE-J1H-CZ-B1 | CONVERTER MOD DC/DC 52V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8760ETL+ | 功能描述:电流型 PWM 控制器 Dual-Phase Quick PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8760ETL+T | 功能描述:电流型 PWM 控制器 Dual-Phase Quick PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8760ETL-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8760EVKIT | 功能描述:电流型 PWM 控制器 Evaluation Kit for the MAX8760 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8761ETG+ | 功能描述:LCD 驱动器 Linear-Regulator LCD Panel Power Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。