- 您现在的位置：买卖IC网 > PDF目录13115 > MAX8760ETL+ (Maxim Integrated Products)IC CNTRLR QUICK PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX8760ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/39页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR QUICK PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，6 位 VID AMD 移动式 Turion? |
| 输入电压： | 4 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 0.38 V ~ 1.55 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页
Dual-Phase, Quick-PWM Controller for AMD
Mobile Turion 64 CPU Core Power Supplies
Power-On Reset
Power-on reset (POR) occurs when V CC rises above
approximately 2V, resetting the fault latch, activating
boot mode, and preparing the PWM for operation. V CC
undervoltage lockout (UVLO) circuitry inhibits switch-
ing, and forces the DL gate driver high (to enforce out-
I LOAD = I LOAD(MAX) x 80%.
For multiphase systems, each phase supports a
fraction of the load, depending on the current bal-
ancing. When properly balanced, the load current is
evenly distributed among each phase:
put overvoltage protection). When V CC rises above
4.25V, the DAC inputs are sampled and the output volt-
age begins to slew to the target voltage.
I LOAD ( PHASE ) =
I LOAD
η TOTAL
For automatic startup, the battery voltage should be
present before V CC . If the Quick-PWM controller
attempts to bring the output into regulation without the
battery voltage present, the fault latch trips. Toggle the
SHDN pin to reset the fault latch.
Input Undervoltage Lockout
During startup, the V CC UVLO circuitry forces the DL
gate driver high and the DH gate driver low, inhibiting
switching until an adequate supply voltage is reached.
Once V CC rises above 4.25V, valid transitions detected
?
?
where η TOTAL is the total number of active phases.
Switching frequency: This choice determines the
basic trade-off between size and efficiency. The
optimal frequency is largely a function of maximum
input voltage due to MOSFET switching losses that
are proportional to frequency and V IN 2 . The opti-
mum frequency is also a moving target, due to rapid
improvements in MOSFET technology that are mak-
ing higher frequencies more practical.
Inductor operating point: This choice provides
L = η TOTAL ? ? ? ?
at the trigger input initiate a corresponding on-time
pulse (see the On-Time One-Shot (TON) section). If the
V CC voltage drops below 4.25V, it is assumed that
there is not enough supply voltage to make valid deci-
sions. To protect the output from overvoltage faults, the
controller activates the shutdown sequence.
Multiphase Quick-PWM
Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency
and inductor operating point (ripple-current ratio). The
primary design trade-off lies in choosing a good switch-
ing frequency and inductor operating point, and the fol-
lowing four factors dictate the rest of the design:
? Input voltage range: The maximum value
(V IN(MAX) ) must accommodate the worst-case high
AC adapter voltage. The minimum value (V IN(MIN) )
must account for the lowest input voltage after drops
due to connectors, fuses, and battery-selector
switches. If there is a choice at all, lower input volt-
ages result in better efficiency.
trade-offs between size vs. efficiency and transient
response vs. output noise. Low inductor values pro-
vide better transient response and smaller physical
size, but also result in lower efficiency and higher out-
put noise due to increased ripple current. The mini-
mum practical inductor value is one that causes the
circuit to operate at the edge of critical conduction
(where the inductor current just touches zero with
every cycle at maximum load). Inductor values lower
than this grant no further size-reduction benefit. The
optimum operating point is usually found between
20% and 50% ripple current.
Inductor Selection
The switching frequency and operating point (% ripple
current or LIR) determine the inductor value as follows:
? V IN ? V OUT ? ? V OUT ?
? f SW I LOAD ( MAX ) LIR ? ? V IN ?
where η TOTAL is the total number of phases.
Find a low-loss inductor having the lowest possible DC
resistance that fits in the allotted dimensions. Ferrite
?
Maximum load current: There are two values to
consider. The peak load current (I LOAD(MAX) ) deter-
mines the instantaneous component stresses and fil-
tering requirements, and thus drives output capacitor
selection, inductor saturation rating, and the design
cores are often the best choice, although powdered
iron is inexpensive and can work well at 200kHz. The
core must be large enough not to saturate at the peak
inductor current (I PEAK ):
I PEAK = ? LOAD ( MAX ) ? ? 1 +
2 ?
of the current-limit circuit. The continuous load cur-
rent (I LOAD ) determines the thermal stresses and
thus drives the selection of input capacitors,
MOSFETs, and other critical heat-contributing com-
ponents. Modern notebook CPUs generally exhibit
? I ? ?
? η TOTAL ? ?
LIR ?
?
______________________________________________________________________________________
31
相关PDF资料 |
PDF描述 |
|---|---|
| RCB40DHLN | CONN EDGECARD 80POS DIP .050 SLD |
| MAX17528GTJ+ | IC PWM CTRLR STP-DWN 32TQFN-EP |
| RYM12DRST-S664 | CONN EDGECARD 24POS DIP .156 SLD |
| MAX17036GTL+ | IC CTRLR VID QUICK-PWM 40-TQFN |
| VE-J1H-CZ-B1 | CONVERTER MOD DC/DC 52V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8760ETL+ | 功能描述:电流型 PWM 控制器 Dual-Phase Quick PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8760ETL+T | 功能描述:电流型 PWM 控制器 Dual-Phase Quick PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8760ETL-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8760EVKIT | 功能描述:电流型 PWM 控制器 Evaluation Kit for the MAX8760 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8761ETG+ | 功能描述:LCD 驱动器 Linear-Regulator LCD Panel Power Supply RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。