- 您现在的位置：买卖IC网 > PDF目录80516 > MB91F465PAPMC-GSE2 (FUJITSU LTD) RISC MICROCONTROLLER, PQFP176 PDF资料下载
参数资料
| 型号： | MB91F465PAPMC-GSE2 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | RISC MICROCONTROLLER, PQFP176 |
| 封装： | 24 X 24 MM, 0.50 MM PITCH, LEAD FREE, PLASTIC, LQFP-176 |
| 文件页数： | 162/200页 |
| 文件大小： | 6566K |
| 代理商： | MB91F465PAPMC-GSE2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页当前第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页
MB91460P Series
64
DS07-16615-2E
■ HANDLING DEVICES
1.
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage higher than (VDD5, VDD35 or HVDD5 *1) or less than (VSS5 or
HVSS5 *1) is applied to an input or output pin or if a voltage exceeding the rating is applied between the power
supply pins and ground pins. If latch-up occurs, the power supply current increases rapidly, sometimes resulting
in thermal breakdown of the device. Therefore, be very careful not to apply voltages in excess of the absolute
maximum ratings.
Note *1: HVDD5, HVSS5 are available only on devices having Stepper Motor Controller.
2.
Handling of unused input pins
If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected
to pull-up or pull-down resistor (2K
Ω to 10KΩ) or enable internal pullup or pulldown resisters (PPER/PPCR)
before the input enable (PORTEN) is activated by software. The mode pins MD_x can be connected to VSS5 or
VDD5 directly. Unused ALARM input pins can be connected to AVSS5 directly.
3.
Power supply pins
In MB91460 series, devices including multiple power supply pins and ground pins are designed as follows; pins
necessary to be at the same potential are interconnected internally to prevent malfunctions such as latch-up.
All of the power supply pins and ground pins must be externally connected to the power supply and ground
respectively in order to reduce unnecessary radiation, to prevent strobe signal malfunctions due to the ground
level rising and to follow the total output current ratings. Furthermore, the power supply pins and ground pins of
the MB91460 series must be connected to the current supply source via a low impedance.
It is also recommended to connect a ceramic capacitor of approximately 0.1
μF as a bypass capacitor between
power supply pin and ground pin near this device.
This series has a built-in step-down regulator. Connect a bypass capacitor of 4.7
μF (use a X7R ceramic
capacitor) to VCC18C pin for the regulator.
4.
Crystal oscillator circuit
Noise in proximity to the X0 (X0A) and X1 (X1A) pins can cause the device to operate abnormally. Printed circuit
boards should be designed so that the X0 (X0A) and X1 (X1A) pins, and crystal oscillator, as well as bypass
capacitors connected to ground, are located near the device and ground.
It is recommended that the printed circuit board layout be designed such that the X0 and X1 pins or X0A and
X1A pins are surrounded by ground plane for the stable operation.
Please request the oscillator manufacturer to evaluate the oscillational characteristics of the crystal and this
device.
5.
Notes on using external clock
When using the external clock, it is necessary to simultaneously supply the X0 (X0A) and the X1 (X1A) pins. In
the described combination, X1 (X1A) should be supplied with a clock signal which has the opposite phase to
the X0 (X0A) pins. At X0 and X1, a frequency up to 16 MHz is possible.
(Continued)
相关PDF资料 |
PDF描述 |
|---|---|
| MB95F353LPF-G-SNE2 | MICROCONTROLLER, PDSO24 |
| MPC8560CVT667JC | 32-BIT, 667 MHz, RISC PROCESSOR, PBGA783 |
| M926-02I622.0800 | 622.08 MHz, OTHER CLOCK GENERATOR, CQCC36 |
| M928-02-700.0000 | 700 MHz, OTHER CLOCK GENERATOR, CQCC36 |
| MK1411SLF | 35.46896 MHz, VIDEO CLOCK GENERATOR, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F465X | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:The Ultimate Automotive Network |
| MB91F465XAPMC-ESE2 | 制造商:FUJITSU 功能描述: |
| MB91F465XAPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB91F466BA | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F466HAPMC-GSE2 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。