- 您现在的位置：买卖IC网 > PDF目录16633 > MC33911BAC (Freescale Semiconductor)IC SYSTEM BASIS CHIP 32LQFP PDF资料下载
参数资料
| 型号： | MC33911BAC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 25/92页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP 32LQFP |
| 标准包装： | 250 |
| 应用： | 系统基础芯片 |
| 电流 - 电源： | 4.5mA |
| 电源电压： | 5.5 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MC33911G5AC/MC3433911G5AC
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
RESET PIN (RST)
This bidirectional pin is used to reset the MCU in case the
33911 detects a reset condition, or to inform the 33911 that
the MCU has just been reset. After release of the RST pin,
Normal Request mode is entered.
The RST pin is an active low filtered input and output formed
by a weak pull-up and a switchable pull-down structure which
allows this pin to be shorted either to V DD or to GND during
software development, without the risk of destroying the
driver.
INTERRUPT PIN (IRQ)
The IRQ pin is a digital output used to signal events or faults
to the MCU while in Normal and Normal Request mode or to
signal a wake-up from Stop mode. This active low output will
transition to high only after the interrupt is acknowledged by
a SPI read of the respective status bits.
WATCHDOG CONFIGURATION PIN (WDCONF)
The WDCONF pin is the configuration pin for the internal
watchdog. A resistor can be connected to this pin to configure
the window watchdog period. When connected directly to
ground, the watchdog will be disabled. When this pin is left
open, the watchdog period is fixed to its lower precision
internal default value (150 ms typical).
GROUND CONNECTION PINS (AGND, PGND,
LGND)
The AGND, PGND and LGND pins are the Analog and Power
ground pins.
The AGND pin is the ground reference of the voltage
regulator.
The PGND and LGND pins are used for high current load
return as in the relay-drivers and LIN interface pin.
Note: PGND, AGND and LGND pins must be connected
together.
LOW SIDE PINS (LS1 AND LS2)
LS1 and LS2 are the low side driver outputs. Those outputs
are short-circuit protected and include active clamp circuitry
to drive inductive loads. Due to the energy clamp voltage on
this pin, it can raise above the battery level when switched off.
The switches are controlled through the SPI and can be
configured to respond to a signal applied to the PWMIN input
pin.
Both low side switches are protected against overheating. In
case of VS1 disconnection and the low sides are still supplied
by V BAT through a load, both low sides will have a VDS
voltage equal to the clamping value, as stated in the
specification.
DIGITAL/ANALOG PINS (L1 AND L2)
The Lx pins are multi purpose inputs. They can be used as
digital inputs, which can be sampled by reading the SPI and
used for wake-up when 33911 is in low power mode or used
as analog inputs for the analog multiplexer. When used to
sense voltage outside the module, a 33 kohm series resistor
must be used on each input.
When used as wake-up inputs L1 and L2 can be configured
to operate in cyclic-sense mode. In this mode the high side
switch is configured to be periodically turned on and sample
the wake-up inputs. If a state change is detected between two
cycles a wake-up is initiated. The 33911 can also wake-up
from Stop or Sleep by a simple state change on L1 and L2.
When used as analog inputs, the voltage present on the Lx
pins is scaled down by an selectable internal voltage divider
and can be routed to the ADOUT0 output through the analog
multiplexer.
Note: If an Lx input is selected in the analog multiplexer, it will
be disabled as a digital input and remains disabled in low
power mode. No wake-up feature is available in that
condition.
When an Lx input is not selected in the analog multiplexer,
the voltage divider is disconnected from that input.
HIGH SIDE OUTPUT PIN (HS1)
This high side switch is able to drive loads such as relays or
lamps. Its structure is connected to the VS2 supply pin. The
pin is short-circuit protected and also protected against
overheating.
HS1 is controlled by SPI and can respond to a signal applied
to the PWMIN input pin.
The HS1 output can also be used during low-power mode for
the cyclic-sense of the wake inputs.
POWER SUPPLY PINS (VS1 AND VS2)
Those are the battery level voltage supply pins. In an
application, VS1 and VS2 pins must be protected against
reverse battery connection and negative transient voltages
with external components. These pins sustain standard
automotive voltage conditions such as a load dump at 40 V.
The high side switch (HS1) is supplied by the VS2 pin. All
other internal blocks are supplied by the VS1 pin.
33911
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
25
相关PDF资料 |
PDF描述 |
|---|---|
| Q2-F-3/16-01-QX30FT | HEATSHRNK POLY Q2F 3/16" BLK 30' |
| 127R14-699B | CABLE FLAT FLEX 14POS 1.27MM 27. |
| 050R33-330B | CABLE FLAT FLEX 33POS .5MM 13" |
| RCM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
| ABC05DRYN-S13 | CONN EDGECARD 10POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33911BACR2 | 功能描述:LIN 收发器 SBC LIN2G MEDIUM END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911G5AC | 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911G5ACR2 | 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33912BAC | 功能描述:LIN 收发器 SBC LIN2G - HI END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33912BACR2 | 功能描述:LIN 收发器 SBC LIN2G - HI END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。