- 您现在的位置：买卖IC网 > PDF目录16633 > MC33911BAC (Freescale Semiconductor)IC SYSTEM BASIS CHIP 32LQFP PDF资料下载
参数资料
| 型号： | MC33911BAC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 27/92页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP 32LQFP |
| 标准包装： | 250 |
| 应用： | 系统基础芯片 |
| 电流 - 电源： | 4.5mA |
| 电源电压： | 5.5 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MC33911G5AC/MC3433911G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
INTRODUCTION
The 33911 offers three main operating modes: Normal (Run),
Stop, and Sleep (Low Power). In Normal mode, the device is
active and is operating under normal application conditions.
The Stop and Sleep modes are low power modes with wake-
up capabilities.
In Stop mode, the voltage regulator still supplies the MCU
with V DD (limited current capability), while in Sleep mode the
voltage regulator is turned off (V DD = 0 V).
Wake-up from Stop mode is initiated by a wake-up interrupt.
Wake-up from Sleep mode is done by a reset and the voltage
regulator is turned back on.
The selection of the different modes is controlled by the
MOD1:2 bits in the Mode Control Register (MCR).
Figure 14 describes how transitions are done between the
different operating modes. Table 5 , gives an overview of the
operating modes.
RESET MODE
The 33911 enters the Reset mode after a power up. In this
mode, the RST pin is low for 1.0 ms (typical value). After this
delay, it enters the Normal Request mode and the RST pin is
driven high.
The Reset mode is entered if a reset condition occurs (V DD
low, watchdog trigger fail, after wake-up from Sleep mode,
Normal Request mode timeout occurs).
NORMAL REQUEST MODE
This is a temporary mode automatically accessed by the
device after the Reset mode, or after a wake-up from Stop
mode.
In Normal Request mode, the VDD regulator is ON, the
RESET pin is High, and the LIN is operating in RX Only
mode.
As soon as the device enters in the Normal Request mode an
internal timer is started for 150 ms (typical value). During
these 150 ms, the MCU must configure the Timing Control
Register (TIMCR) and the Mode Control Register (MCR) with
MOD2 and MOD1 bits set = 0, to enter the Normal mode. If
within the 150 ms timeout, the MCU does not command the
33911 to Normal mode, it will enter in Reset mode. If the
WDCONF pin is grounded in order to disable the watchdog
function, it goes directly in Normal mode after the Reset
mode.
NORMAL MODE
The VDD regulator is ON and delivers its full current
capability.
If an external resistor is connected between the WDCONF
pin and the Ground, the window watchdog function will be
enabled.
The wake-up inputs (L1 and L2) can be read as digital inputs
or have its voltage routed through the analog-multiplexer.
The LIN interface has slew rate and timing compatible with
the LIN protocol specification 2.0, 2.1 and SAEJ2602. The
LIN bus can transmit and receive information.
The high side and low side switches are active and have
PWM capability according to the SPI configuration.
The interrupts are generated to report failures for V SUP over/
under-voltage, thermal shutdown, or thermal shutdown
prewarning on the main regulator.
SLEEP MODE
The Sleep mode is a low power mode. From Normal mode,
the device enters into Sleep mode by sending one SPI
command through the Mode Control Register (MCR), or (V DD
low > 150 ms) with V SUV = 0. When in Reset mode, a V DD
under-voltage condition with no V SUP under-voltage (V SUV =
0) will send the device to Sleep mode. All blocks are in their
lowest power consumption condition. Only some wake-up
sources (wake-up inputs with or without cyclic sense, forced
wake-up and LIN receiver) are active. The 5.0 V regulator is
OFF. The internal low-power oscillator may be active if the IC
is configured for cyclic-sense. In this condition, the high side
switch is turned on periodically and the wake-up inputs are
sampled.
Wake-up from Sleep mode is similar to a power-up. The
device goes in Reset mode except that the SPI will report the
wake-up source and the BATFAIL flag is not set.
STOP MODE
The Stop mode is the second low power mode, but in this
case the 5.0 V regulator is ON with limited current drive
capability. The application MCU is always supplied while the
33911 is operating in Stop mode.
The device can enter into Stop mode only by sending the SPI
command. When the application is in this mode, it can wake-
up from the 33911 side (for example: cyclic sense, force
wake-up, LIN bus, wake inputs) or the MCU side (CS, RST
pins). Wake-up from Stop mode will transition the 33911 to
Normal Request mode and generates an interrupt except if
the wake-up event is a low to high transition on the CS pin or
comes from the RST pin.
In Normal mode, all 33911 functions are active and can be
controlled by the SPI interface and the PWMIN pin.
33911
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
27
相关PDF资料 |
PDF描述 |
|---|---|
| Q2-F-3/16-01-QX30FT | HEATSHRNK POLY Q2F 3/16" BLK 30' |
| 127R14-699B | CABLE FLAT FLEX 14POS 1.27MM 27. |
| 050R33-330B | CABLE FLAT FLEX 33POS .5MM 13" |
| RCM15DRYH-S13 | CONN EDGECARD 30POS .156 EXTEND |
| ABC05DRYN-S13 | CONN EDGECARD 10POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33911BACR2 | 功能描述:LIN 收发器 SBC LIN2G MEDIUM END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911G5AC | 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33911G5ACR2 | 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33912BAC | 功能描述:LIN 收发器 SBC LIN2G - HI END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MC33912BACR2 | 功能描述:LIN 收发器 SBC LIN2G - HI END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。