参数资料
型号: MC33911BAC
厂商: Freescale Semiconductor
文件页数: 29/92页
文件大小: 0K
描述: IC SYSTEM BASIS CHIP 32LQFP
标准包装: 250
应用: 系统基础芯片
电流 - 电源: 4.5mA
电源电压: 5.5 V ~ 27 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 32-LQFP
供应商设备封装: 32-LQFP(7x7)
包装: 托盘
MC33911G5AC/MC3433911G5AC
FUNCTIONAL DEVICE OPERATIONS
OPERATIONAL MODES
Table 5. Operating Modes Overview
Function
Reset Mode Normal Request Mode
Normal
Mode
Stop Mode
Sleep Mode
VDD
LSx
HS1
Analog Mux
Lx
Full
-
-
-
-
Full
SPI/PWM (60)
SPI/PWM (60)
SPI
Inputs
Full
SPI/PWM
SPI/PWM
SPI
Inputs
Stop
-
Note (61)
-
Wake-up
-
-
Note (62)
-
Wake-up
LIN
-
Rx-Only
Full/Rx-Only Rx-Only/Wake-up
Wake-up
/Off
Watchdog
-
150 ms (typ.) timeout
On
-
-
Voltage Monitoring
V SUP /V DD
V SUP /V DD
V SUP /V DD
V DD
-
Notes
60.
61.
62.
63.
INTERRUPTS
Operation can be controlled by the PWMIN input.
HS1 switch can be configured for cyclic sense operation in Stop mode.
HS1 switch can be configured for cyclic sense operation in Sleep mode.
Windowing operation when enabled by an external resistor.
High-voltage Interrupt:
Interrupts are used to signal a microcontroller that a
peripheral needs to be serviced. The interrupts which can be
generated, change according to the operating mode. While in
Normal and Normal Request modes, the 33911 signals
through interrupts special conditions which may require a
MCU software action. Interrupts are not generated until all
pending wake-up sources are read in the Interrupt Source
Register (ISR).
While in Stop mode, interrupts are used to signal wake-up
events. Sleep mode does not use interrupts. Wake-up is
performed by powering-up the MCU. In Normal and Normal
Request mode the wake-up source can be read by SPI.
The interrupts are signaled to the MCU by a low logic level of
the IRQ pin, which will remain low until the interrupt is
acknowledged by a SPI read command of the ISR register.
The IRQ pin will then be driven high.
Interrupts are only asserted while in Normal, Normal Request
and Stop mode. Interrupts are not generated while the RST
pin is low.
The following is a list of the interrupt sources in Normal and
Normal Request modes. Some of these can be masked by
writing to the SPI - Interrupt Mask Register (IMR).
Signals when the supply line (VS1) voltage increases above
the VSOV threshold ( V SOV ).
Over-temperature Prewarning:
Signals when the 33911 temperature has reached the pre-
shutdown warning threshold. It is used to warn the MCU that
an over-temperature shutdown in the main 5.0 V regulator is
imminent.
LIN Over-temperature Shutdown / TXD Stuck At
Dominant / RXD Short-circuit:
These signal fault conditions within the LIN interface will
cause the LIN driver to be disabled. In order to restart the
operation, the fault must be removed and TXD must go
recessive.
High Side Over-temperature Shutdown:
Signals a shutdown in the high side output.
Low Side Over-temperature Shutdown:
Signals a shutdown in the low side outputs.
Low-voltage Interrupt:
Signals when the supply line (VS1) voltage drops below the
VSUV threshold ( V SUV ).
33911
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
29
相关PDF资料
PDF描述
Q2-F-3/16-01-QX30FT HEATSHRNK POLY Q2F 3/16" BLK 30'
127R14-699B CABLE FLAT FLEX 14POS 1.27MM 27.
050R33-330B CABLE FLAT FLEX 33POS .5MM 13"
RCM15DRYH-S13 CONN EDGECARD 30POS .156 EXTEND
ABC05DRYN-S13 CONN EDGECARD 10POS .100 EXTEND
相关代理商/技术参数
参数描述
MC33911BACR2 功能描述:LIN 收发器 SBC LIN2G MEDIUM END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MC33911G5AC 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MC33911G5ACR2 功能描述:LIN 收发器 SBC LIN 2.5G Medium end RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MC33912BAC 功能描述:LIN 收发器 SBC LIN2G - HI END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MC33912BACR2 功能描述:LIN 收发器 SBC LIN2G - HI END RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8