- 您现在的位置：买卖IC网 > PDF目录11546 > MC33989DW (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MC33989DW |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 19/72页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 标准包装： | 26 |
| 控制器类型： | 系统基础芯片 |
| 接口： | CAN |
| 电源电压： | 5.5 V ~ 18 V |
| 电流 - 电源： | 45mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 配用： | KIT33989DWEVB-ND - KIT EVAL 33989DW HS SBC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
33989
FUNCTIONAL DEVICE OPERATION
RESET AND WATCHDOG PINS, SOFTWARE WATCHDOG OPERATIONS
SPI WAKE-UP
The device can wake-up by the CS pin in Sleep or Stop modes. Wake-up is detected by the CS pin transition from low to a
high level. In Stop mode, this corresponds with the condition where the MCU and SBC are in Stop mode; and when the
application wake-up event comes through the MCU.
DEVICE POWER-UP, SBC WAKE-UP
After device or system power-up, or after the SBC wakes up from Sleep mode, it enters into Reset mode prior to moving into
Normal Request mode.
DEBUG MODE: HARDWARE AND SOFTWARE DEBUG WITH THE SBC
When the SBC is mounted on the same printed circuit board as the microcontroller it supplies, both application software and
SBC dedicated routine must be debugged. The following features allow debug of the software by allowing the possibility of
disabling the SBC internal software Watchdog timer.
DEVICE POWER-UP, RESET PIN CONNECTED TO VDD1
At SBC power-up the VDD1 voltage is provided, but if no SPI communication occurs to configure the device, a reset occurs
every 350 ms. In order to allow software debug and avoid MCU reset, the Reset pin can be connected directly to VDD1 by a
jumper.
DEBUG MODES WITH SOFTWARE WATCHDOG DISABLED THOUGH SPI (NORMAL DEBUG, STANDBY
AND STOP DEBUG)
The Watchdog software can be disabled through SPI. To avoid unwanted watchdog disable while limiting the risk of disabling
Watchdog during SBC normal operation, the watchdog disable must be achieved the following sequence:
Step 1–Power down the SBC
Step 2–Power-up the SBC (The BATFAIL bit is set, allowing the SBC to enter Normal Request mode)
Step 3–Write to TIM1 register allowing SBC entering Normal mode
Step 4–Write to MCR register with data 0000, enabling the Debug mode. Complete SPI byte: 000 1 0000
Step 5–Write to MCR register normal debug (0001x101)
Step 6–To leave the Debug mode, write 0000 to MCR register
While in Debug mode, the SBC can be used without having to clear the WD on a regular basis to facilitate software and
hardware debug.
At Step 2, the SBC is in Normal Request. Steps 3, 4, and 5 should be completed consecutively and within the 350 ms time
period of the Normal Request mode. If this step is not accomplished in a timely manner, the SBC will go into Reset mode, entering
Normal Request again.
When the SBC is in Debug mode, and set in Stop Debug or Sleep Debug, when a wake-up occurs the SBC enters Normal
Request mode for a time period of 350 ms. To avoid the SBC generating a reset (enter Reset mode) the desired next Debug
mode (Normal Debug or Standby Debug) should be configured within the 350 ms time period of the Normal Request mode. For
details, please refer to State Machine in Debug mode, Figure 16.
To avoid entering Debug mode after a power-up, first read BATFAIL bit (MCR read) and write 0000 into MCR. Figure 15
illustrates the Debug mode enter.
Figure 11. Debug Mode Enter
VSUP
SPI
MCR(Step4)
Batfail
VDD1
Debug Mode
MCR (Step5)
SPI: Read Batfail
MCR (Step6)
SBC in Debug Mode, No WD
SBC Not in Debug Mode and WD ON
TIM1(Step 3)
相关PDF资料 |
PDF描述 |
|---|---|
| MC33889DW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33389CDW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
| PX0414 | CONN SMB JACK PNL MNT RG174 |
| PIC16LF1937-E/PT | IC PIC MCU FLASH 512KX14 44-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33989DWR2 | 功能描述:CAN 接口集成电路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33989PEG | 功能描述:CAN 接口集成电路 SBC-HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33989PEGR2 | 功能描述:CAN 接口集成电路 SBC-HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。