参数资料
型号: MC33989DW
厂商: Freescale Semiconductor
文件页数: 46/72页
文件大小: 0K
描述: IC SYSTEM BASE W/CAN 28-SOIC
标准包装: 26
控制器类型: 系统基础芯片
接口: CAN
电源电压: 5.5 V ~ 18 V
电流 - 电源: 45mA
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 28-SOIC(0.295",7.50mm 宽)
供应商设备封装: 28-SOIC W
包装: 管件
配用: KIT33989DWEVB-ND - KIT EVAL 33989DW HS SBC
Analog Integrated Circuit Device Data
50
Freescale Semiconductor
33989
TYPICAL APPLICATIONS
SUPPLEMENTAL APPLICATION NOTES
T1: Is dependent on the selected cyclic sense timing in the TIM2 register (5.0 to 400 ms). LX is sampled 10 s before the
end of cyclic sense on time. If the LX correct wake-up level happens just after sample point, the wake-up will be detected
at the next HS1 activation and a complete period is lost.
T2: It is the same than Lx to INT pulse: typ 100 s
The total time is around 5.13 ms (for a cyclic sense total time of 5.0 ms) in the above example.
MC33989 CAN INTERFACE
This section is a detailed description of the CAN interface of the MC33989.
Block Diagram
Figure 34 is a simplified block diagram of the CAN interface of the MC33989.
Figure 34. 33989 CAN Interface
CAN Interface Supply
The supply voltage for the CAN driver is the V2 pin. The CAN interface also has a supply path from the battery line, through
the pin VSUP. This path is used in CAN sleep mode to allow wake-up detection.
During CAN communication (transmission and reception) the CAN interface current is sourced from the V2 pin. During a CAN
low power mode, the current is sourced from the VSUP pin.
Main Operation Modes Description
The CAN interface of the MC33989 has two main operation modes: Normal mode and sleep mode. The modes are controlled
by the SPI command.
In normal mode, used for communication, four different slew rates are available for the user.
In sleep mode, the user has the option to enable or disable the remote CAN wake-up capability.
CAN Driver Operation in Normal Mode
When the CAN interface of the MC33989 is in Normal mode, the driver has two states: recessive or dominant. The driver state
is controlled by the TX pin. The bus state is reported through the RX pin.
When TX is high, the driver is set in a recessive state, CANH and CANL lines are biased to the voltage set at V2 divided by
2, approx. 2.5 V.
When TX is low, the bus is set into dominant state: the CANL and CANH drivers are active. CANL is pulled to gnd, CANH is
pulled high toward 5.0 V (the voltage at V2).
The RX pin reports the bus state: the CANH minus the CANL voltage is compared versus an internal threshold (a few hundred
mV). If “CANH minus CANL” is below the threshold, the bus is recessive and RX is set high.
V2
Bus termination (60 ohms)
CANH line
CAN L line
TX
RX
Differential
receiver
Driver
2.5V
Wake-up
receiver
pattern
recognition
Internal
VSUP
wake-up
signal
CANH
CANL
SPI control
V2
QH
QL
相关PDF资料
PDF描述
MC33889DW IC SYSTEM BASE W/CAN 28-SOIC
MC33389CDW IC SYSTEM BASE W/CAN 28-SOIC
MC33388DR2 IC TOLERANT CAN INT FAULT 14SOIC
PX0414 CONN SMB JACK PNL MNT RG174
PIC16LF1937-E/PT IC PIC MCU FLASH 512KX14 44-TQFP
相关代理商/技术参数
参数描述
MC33989DWR2 功能描述:CAN 接口集成电路 SBC HIGH SPEED RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube
MC33989PEG 功能描述:CAN 接口集成电路 SBC-HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube
MC33989PEGR2 功能描述:CAN 接口集成电路 SBC-HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube
MC33990D 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC(0.295",7.50mm 宽) 供应商设备封装:16-SOIC 包装:带卷 (TR)
MC33990DR2 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC(0.295",7.50mm 宽) 供应商设备封装:16-SOIC 包装:带卷 (TR)