- 您现在的位置：买卖IC网 > PDF目录20771 > MC34844EPR2 (Freescale Semiconductor)IC LED DVR BACKLIGHT 10CH 32QFN PDF资料下载
参数资料
| 型号： | MC34844EPR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 18/62页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR BACKLIGHT 10CH 32QFN |
| 视频文件： | LED backlighting with MC34844 |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 频率： | 可调节/可选择 |
| 电源电压： | 7 V ~ 28 V |
| 输出电压： | 8 V ~ 60 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
| 配用： | KIT34844EPEVME-ND - BOARD EVAL 10CH MC34844 LED DVR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
MC34844
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
Also the device has a precharge voltage that add 0.5 Volts
to the Boost, cycle by cycle of the PWM. It helps the boost to
respond faster every time the load turns back on again.
CURRENT MIRROR
The programmable current mirror matches the current in
10 LED strings to within 2%. The maximum current is set
using a resistor to GND from the ISET pin. This can be scaled
down using the I 2 C interface to 255 levels.
Zero current is achieved by turning off the LED Driver by
I 2 C (registers CHENx = 0 h) for a duty cycle from 0% to 99%
or by pulling PWM pin low regardless of the duty cycle.
I 2 C capability allows the channels to be controlled
individually or in parallel.
the LED at a lower frequency than the PWM dimming
frequency (Minimum pulse width = 150 ns).
A pulsed mode can also be programmed using the I 2 C
interface (STROBE bit = 1). In this mode, each rising edge of
the PWM signal turns on the next channel, while turning off
all other channels. The duration that the channel is
illuminated is set by the duty cycle of the PWM input pin. This
can be used to scan the output channels.
DISABLING LED CHANNELS
The 34844 allows the user to enable and disable each of
the 10 channels separately by writing the corresponding
CHENx bit on Registers 08 and 09 thru I 2 C.
When a channel is disabled thru the I 2 C prior the device
Current on LED Channel (PIN and NIN mode disabled)
Eqn. 1
starts to operate, the corresponding LED driver is disabled
but the feedback circuit is still connected. This may interfere
Current [ A ] = -----------------------------------------------------------
PWMFrequency [ Hz ] = --------------------------------------------------------------------
ICH [ RegisterValue ]
RSET [ ohms ]
In the off state, the LEDs current is set to 0 and the boost
converter stops switching.
This feature allows to drive more than 50 mA of current by
connecting the LED string to 2 or more LED channels in
parallel. For example; if the application requires to drive 5
channels at 100 mA, then the bottom of each LED string
should be connected to two channels in order to duplicate the
current capability (Example: CH0+CH1 = 100 mA).
PWM GENERATOR
The PWM generator can operate in either master or slave
modes, as set by the M/~S pin.
In master mode, the internal PWM generator frequency is
programmed through the I 2 C interface (registers FPWM).
The default programmed value set the number of 25 kHz
clocks (40 μ s) in one PWM cycle. The 18-bit resolution allows
minimum PWM frequencies of 100 Hz to be programmed.
The resulting frequency is output on the CK pin.
PWM Frequency Eqn. 2
19.2Mhz
FPWM [ RegisterValue ]
In slave mode, the CK pin acts as an input. The internal
digital PLL uses this frequency as the PWM frequency. By
setting one device as master, and connecting the CK output
to the input on a number of slave configured devices, all
PWM frequencies are synchronized together.
The duty cycle of the PWM waveform in both master and
slave modes is set using a second register on the I 2 C
interface (register DPWM), and can be controlled from 100%
duty cycle to 1/256 T PWM = 0.39%. Zero percent of duty cycle
is achieved by turning LED drivers off (register CHENx = 0h)
or pulling PWM pin low.
An external PWM can also be used. The PWM input is
'AND'ed with the internal signal. By setting the serial interface
to 100% duty cycle (default), the external pin has full control
of the PWM duty cycle. This pin can also be used to modulate
with the operation of the dynamic headroom control (DHC)
which can lead to erratic output voltage regulation. For this
condition, the output voltage may ramp up to the OVP level if
the voltage on the LED driver is not substantially above the
DHC regulation voltage (0.75 V typ). Because of this
operation under I 2 C/SMBUS Mode, we recommend to
connect the unused channels to VDC2 thru a100 kohm
resistor and also follow the below powering up sequence:
1. PWM pin = Low.
2. Power up the part.
3. Program the I 2 C commands and disable the unused
channels.
4. Enable the Boost and current drivers by taking PWM
pin to HIGH.
This previous device's operation does not happen when all
channels are being used because the voltage across the LED
drivers is always equal or higher than the DHC regulation
voltage (0.75 V typ). For this condition, the user can disable/
enable any of the channels thru I 2 C without causing any
erratic behavior but the FAIL pin cannot be cleared. If FAIL
pin is to be cleared thru I 2 C, it will be necessary to use the
suggested configuration shown at the FAIL PIN session.
FAIL PIN
If a LED fails open in any of the LED strings, the voltage in
that particular LED channel will be close to ground and the
LED open failure is detected. When this happens, a failure is
registered, the FAIL pin is set to its high-impedance stage,
and the channel is turned off.
The FAIL pin cannot be cleared for manual mode unless a
complete power on reset is applied. However for I 2 C/SMBUS
mode, the FAIL pin is cleared by disabling the malfunction
channels (CHENx = 0) and clearing the failure bit (CLRFAIL
bit = 1).
If the application only requires clearing the failure for the
floating or unused channels, then the unused channels must
be connected to VDC2 thru a 100 kohm resistor to avoid
reach instability problems. This will allow detecting another
failure from the connected channels. (See Figure 6 )
34844
Analog Integrated Circuit Device Data
Freescale Semiconductor
18
相关PDF资料 |
PDF描述 |
|---|---|
| HCC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| HBC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| TAP686K025CRW | CAP TANT 68UF 25V 10% RADIAL |
| GSC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
| GMC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34845 | 制造商:SPC Multicomp 功能描述:RECEPTACLE FREE 16WAY 制造商:SPC Multicomp 功能描述:RECEPTACLE, FREE, 16WAY |
| MC34845AEP | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845AEPR2 | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845BEP | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| MC34845BEPR2 | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。