- 您现在的位置：买卖IC网 > PDF目录20771 > MC34844EPR2 (Freescale Semiconductor)IC LED DVR BACKLIGHT 10CH 32QFN PDF资料下载
参数资料
| 型号： | MC34844EPR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 47/62页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR BACKLIGHT 10CH 32QFN |
| 视频文件： | LED backlighting with MC34844 |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 频率： | 可调节/可选择 |
| 电源电压： | 7 V ~ 28 V |
| 输出电压： | 8 V ~ 60 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
| 配用： | KIT34844EPEVME-ND - BOARD EVAL 10CH MC34844 LED DVR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
MC34844A
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
DISABLING LED CHANNELS
The 34844A allows the user to enable and disable each of
the 10 channels separately by writing the corresponding
CHENx bit on Registers 08 and 09 thru I2C.
Since the enable and disable functions reconnects the
feedback circuit of the LED drivers, this shouldn’t be used on
any channel that shuts down either because an open LED
functionality, the 80 mA maximum current is achieved at the
higher allowed level of PIN/NIN pins, ensuring the maximum
current of the LED Drivers are not exceeded.
The optical and temperature control loop can be disabled
by I 2 C setting bits (PINEN & NINEN), or by tying PIN and NIN
pins high (>2.2 V). The LED Driver maximum current is set to
80 mA by using a 3.48 kohm resistor at the ISET pin.
IDIM [ A ] = ISINK [ A ] × ------------------------
×
( VSET – VNIN ) [ V ]
channel condition or because is was previously POWER
OFF. This could cause instability issues since the voltage on
this open LED driver is not substantially above the DHC
regulation voltage (0.75 V typ) and may interfere with the
operation of the dynamic headroom control (DHC) which can
lead to erratic output voltage regulation
FAIL PIN
Current on LED Channel (PIN mode)
VPIN [ V ]
2
Current on LED Channel (NIN mode)
IDIM [ A ] = ISINK [ A ] ----------------------------------------------------
2
Current on LED Channel (PIN+NIN mode)
Eqn. 8
Eqn. 9
Eqn. 10
( VSET + VPIN – VNIN ) [ V ]
If a LED fails open in any of the LED strings, the voltage in
that particular LED channel will be close to ground and the
IDIM [ A ] = ISINK [ A ]
×
--------------------------------------------------------------------------
2
LED open failure is detected. When this happens, a failure is
registered, the FAIL pin is set to its high-impedance stage,
and the channel is shut down.
The FAIL pin cannot be cleared for manual mode unless a
complete power on reset is applied.
However for I 2 C/SMBUS mode, the FAIL pin can be
cleared by cycling the clear fail bit (CLRFAIL bit = 0 - 1 - 0).
This allows the user to waive any known failure and set the
device for being able to detect any other failure during
operation.
If the fail pin cannot be cleared by software then it indicates
that the failure is because of an over-current in the Boost.
Since this is a critical failure the only way to clear it is by
releasing the part from the over-current condition and then
shutdown the part (Refer to Table 12 )
If I 2 C communication is not present, FAIL condition should
be reset by removing the failure and re-enabling the device
thru the EN pin.
OPTICAL AND TEMPERATURE CONTROL LOOP
The 34844A supports both optical and temperature loop
control.
For temperature loop control, the LED brightness can be
adjusted depending on the temperature of the LEDs.
For optical loop control, the 34844A supports both optical
closed loop backlight control, where the brightness of the
backlight is maintained at a required level by adjusting the
light output, until the desired level is achieved, or with
ambient light control, where the backlight brightness
increases as ambient light increases.
Both temperature and optical loops are supported through
the PIN and NIN pins. Each pin supports a 0 V to V SET
(2.048 V typ.) input range which affects the current through
the LEDs. The PIN pin increases current as the voltage rises
from 0 to V SET . The NIN pin reduces current as the voltage
rises from 0 - V SET .
A 6.98 kohm resistor or higher value must be used at the
ISET pin if the part is configured to use PIN+NIN control loop
VPIN and VNIN is the voltage applied on PIN and NIN pins
correspondingly.
For ISINK formula please refer to Equation 1 .
LED FAILURE PROTECTION
Open LED Protection
If LED fails open in any of the LED strings, the voltage in
that channel will be pulled close to zero, which will cause the
channel to be disabled. As a result, the boost output voltage
will go to the OVP level and then come down to the regulation
level to continue powering the rest of the LED strings.
Short LED Protection
If an LED shorted in any of the LED strings, the device will
continue to operate without interruption. However, if the
shorted LED happens to be in the LED string with the highest
forward voltage, the DHC circuit will automatically regulate
the output voltage with respect to the new highest LED
voltage. If more LEDs are shorted in the same LED string, it
may cause excessive power dissipation in the channel which
may cause the OTT circuit to trip which will completely
shutdown the device.
OVER-TEMPERATURE PROTECTION
The 34844A has an on-chip temperature sensor that
measures die temperature. If the IC temperature exceeds the
OTT threshold, the IC will turn off all power sources inside the
IC (LED drivers, boost and internal regulators) until the
temperature falls below the falling OTT threshold. Once it
comes back on, it will operate with the default configuration
(refer to Table 14 ).
SERIAL INTERFACE CONTROL
The 34844A uses an I 2 C interface capable of operating in
standard (100 kHz) or fast (400 kHz) modes.
The A0/SEN pin can be used an address select pin to
allow more than 2 devices in the system. The A0/SEN pin
should be held low on all chips expect the one to be
addressed, where it is taken HIGH.
34844A
Analog Integrated Circuit Device Data
Freescale Semiconductor
47
相关PDF资料 |
PDF描述 |
|---|---|
| HCC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| HBC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| TAP686K025CRW | CAP TANT 68UF 25V 10% RADIAL |
| GSC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
| GMC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34845 | 制造商:SPC Multicomp 功能描述:RECEPTACLE FREE 16WAY 制造商:SPC Multicomp 功能描述:RECEPTACLE, FREE, 16WAY |
| MC34845AEP | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845AEPR2 | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845BEP | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| MC34845BEPR2 | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。