- 您现在的位置：买卖IC网 > PDF目录20771 > MC34844EPR2 (Freescale Semiconductor)IC LED DVR BACKLIGHT 10CH 32QFN PDF资料下载
参数资料
| 型号： | MC34844EPR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 57/62页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR BACKLIGHT 10CH 32QFN |
| 视频文件： | LED backlighting with MC34844 |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 频率： | 可调节/可选择 |
| 电源电压： | 7 V ~ 28 V |
| 输出电压： | 8 V ~ 60 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
| 配用： | KIT34844EPEVME-ND - BOARD EVAL 10CH MC34844 LED DVR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页当前第57页第58页第59页第60页第61页第62页
LAYOUT GUIDELINES
LAYOUT GUIDELINES
RECOMMENDED STACK-UP
The following table shows the recommended layer stack-
up for the signals to have good shielding and Thermal
Dissipation.
Table 16. Layer Stacking Recommendations
SWITCHING NODE (SWA & SWB)
The components associated to this node must be placed
as close as possible to each other to keep the switching loop
small enough so that it does not contaminate other signals.
However, care must be taken to ensure the copper traces
used to connect these components together on this node are
Layer 1 (Top)
Layer 2 (Inner 1)
Layer 3(Inner 2)
Layer 4 (Bottom)
Stack-Up
Signal
Ground
Signal
Ground
capable to handle the necessary current and voltage.
As a reference, a 10 mils trace with a thickness of 1.0 oz.
of copper is capable of handling one ampere.
Traces for connecting the inductor, input and output caps
should be as wide and short as possible to avoid adding
inductance or resistance to the loop. The placement of these
components should be selected far away from sensitive
signals like compensation, feedback and internal regulators
DECOUPLING CAPS
It is recommended to place decoupling caps of 100 pf at
the beginning and at the end of any power signal traces to
filter high frequency noise.
Decoupling caps of 100 pf should be also placed at the
end of any long trace to cancel antenna effects on it.
These caps should be located as closed as possible to the
point to be decoupled and the connection to GND should be
as short as possible.
SM-BUS/I 2 C COMMUNICATION AND CLOCK
SIGNALS (SDA, SCK AND CK)
To avoid contamination of these signals by nearby high
power or high frequency signals, it is a good practice to shield
them with ground planes placed on adjacent layers. Make
sure the ground plane is uniform through the whole signal
trace length.
to avoid power noise coupling.
COMPENSATION COMPONENTS
Components related with COMP pin need to be placed as
close as possible to the pin.
FEEDBACK SIGNAL
The trace of the feedback signal (VOUT) should be routed
perpendicularly or at 45° on a different layer to avoid coupling
noise, preferably between ground or power planes.
I I n n p p u u t t C C a a p p
S S w w i i t t c c h h i i n n g g N N o o d d e e
On State
DO
Signal
Signal
i
C o m p e n s a t t i o n
F F e e e e d d b b a a c c k k
S S i i g g n n a a l l
Off State
O u t p u t t C a p
Ground Planes
Ground Plane
Figure 32. Recommended shielding for critical signals.
Figure 33. Feedback Signal Tracing
These signals shall not run parallel to power signals or
other clock signals in the same routing layer. If they have to
cross or to be routed close to a power signal, it is a good
practice to trace them perpendicularly or at 45° on a different
layer to avoid coupling noise.
34844
Analog Integrated Circuit Device Data
Freescale Semiconductor
57
相关PDF资料 |
PDF描述 |
|---|---|
| HCC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| HBC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| TAP686K025CRW | CAP TANT 68UF 25V 10% RADIAL |
| GSC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
| GMC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34845 | 制造商:SPC Multicomp 功能描述:RECEPTACLE FREE 16WAY 制造商:SPC Multicomp 功能描述:RECEPTACLE, FREE, 16WAY |
| MC34845AEP | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845AEPR2 | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845BEP | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| MC34845BEPR2 | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。