- 您现在的位置：买卖IC网 > PDF目录20771 > MC34844EPR2 (Freescale Semiconductor)IC LED DVR BACKLIGHT 10CH 32QFN PDF资料下载
参数资料
| 型号： | MC34844EPR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 22/62页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR BACKLIGHT 10CH 32QFN |
| 视频文件： | LED backlighting with MC34844 |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 频率： | 可调节/可选择 |
| 电源电压： | 7 V ~ 28 V |
| 输出电压： | 8 V ~ 60 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
| 配用： | KIT34844EPEVME-ND - BOARD EVAL 10CH MC34844 LED DVR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
MC34844
FUNCTIONAL DEVICE OPERATION
I2C BUS SPECIFICATION
During manual mode, all internal Registers are in Default
Configuration, refer Table 7 , under this configuration the PIN
and NIN pins are enabled to scale the current capability per
string and may be disable by setting 2.2 V in the
corresponding pin.
Also in this mode, the device can be enabled as follows:
+ EN pin + PWM signal (Two Signals): In this
configuration, the PWM signal applied to PWM pin will be in
charge of controlling the LED dimming and a second signal
will enable or disable the chip through the EN pin. Figure 21
+ PWM Signal tied to SDA pin (Just ONE signal): In this
PWM signal applied to PWM pin will be in charge of
controlling LED dimming and enable the device every time
the PWM is active. For this configuration EN pin should be
LOW.
POWER DOWN MODE
If the input voltage falls below the UVLO threshold, the
device enters automatically into power down mode. When in
power down, the supply current is reduced below 2.0 μ A
when there is no I 2 C activity, and it rises up when I 2 C
interface is enabled.
configuration the PWM pin should be tied to SDA pin. The
I 2 C BUS SPECIFICATION
The 34844 is a unidirectional device that can only be written by an external control unit. Since the device is a 7 bit address
device (1110110), the control unit needs to follow a specific data transfer format which is shown in Figure 8 .
Figure 8. A Complete Data Transfer
For a complete data transfer, please use this format in the
following order:
1. START condition
2. The 34844 device address and Write instruction
(R/W = 0)
3. First data pack, it corresponds to the 34844 Register
that needs to be written. (refer to Table )
4. Second data pack, it corresponds to the value that
should be written to that register. (refer to Table )
5. STOP condition
I 2 C variables description:
? START: this condition occurs when SDA changes from
HIGH to LOW while SCK is HIGH.
? ACKNOWLEDGE: The acknowledge clock pulse is
generated by the Master (Control Unit).
? The transmitter releases the SDA line (HIGH) during the
acknowledge clock pulse.
The receiver (34844) must pull down the SDA line during
this acknowledge pulse to indicate that the data was
correctly written.
? Bits in the first byte: The first seven bits of the first bite
make up the slave address. The eighth bit is the LSB (least
significant bit), which determines the direction of the
message (Write = 0)
For the 34844 device, when an address is sent, each of the
devices in a system compares the first seven bits after the
START condition with its address. If they match, the
device considers itself addressed by the control unit as a
slave-receiver.
? STOP: this condition occurs when SDA changes from
LOW to HIGH while SCK is HIGH
For more information about “I 2 C BUS SPECIFICATION”
please refer to the following link:
http://www.nxp.com/acrobat_download/literature/
9398/39340011.pdf
34844
Analog Integrated Circuit Device Data
Freescale Semiconductor
22
相关PDF资料 |
PDF描述 |
|---|---|
| HCC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| HBC60DRES-S93 | CONN EDGECARD 120PS .100 EYELET |
| TAP686K025CRW | CAP TANT 68UF 25V 10% RADIAL |
| GSC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
| GMC50DRYS-S93 | CONN EDGECARD 100PS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34845 | 制造商:SPC Multicomp 功能描述:RECEPTACLE FREE 16WAY 制造商:SPC Multicomp 功能描述:RECEPTACLE, FREE, 16WAY |
| MC34845AEP | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845AEPR2 | 功能描述:LED照明驱动器 6-Ch LED Backlt Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MC34845BEP | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| MC34845BEPR2 | 功能描述:USB 接口集成电路 6-Ch LED Backlt Driver RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。