参数资料
型号: MC68HC705C9AFNE
厂商: Freescale Semiconductor
文件页数: 94/118页
文件大小: 0K
描述: IC MCU 8BIT 44-PLCC
标准包装: 26
系列: HC05
核心处理器: HC05
芯体尺寸: 8-位
速度: 2.1MHz
连通性: SCI,SPI
外围设备: POR,WDT
输入/输出数: 24
程序存储器容量: 16KB(16K x 8)
程序存储器类型: OTP
RAM 容量: 352 x 8
电压 - 电源 (Vcc/Vdd): 3 V ~ 5.5 V
振荡器型: 内部
工作温度: 0°C ~ 70°C
封装/外壳: 44-LCC(J 形引线)
包装: 管件
SPI Registers
MC68HC05C9A Advance Information Data Sheet, Rev. 4.1
Freescale Semiconductor
77
Clearing the MODF bit is accomplished by reading the SPSR (with MODF set), followed by a write to
the SPCR. Control bits SPE and MSTR may be restored by user software to their original state during
this clearing sequence or after the MODF bit has been cleared. When configured as an
MC68HC05C9A, it is also necessary to restore DDRD after a mode fault.
Bits 5 and 3–0 — Not Implemented
These bits always read 0.
10.5.3 Serial Peripheral Data I/O Register
The serial peripheral data I/O register (SPDR), shown in Figure 10-6, is used to transmit and receive data
on the serial bus. Only a write to this register will initiate transmission/reception of another byte and this
will only occur in the master device. At the completion of transmitting a byte of data, the SPIF status bit is
set in both the master and slave devices.
When the user reads the serial peripheral data I/O register, a buffer is actually being read. The first SPIF
must be cleared by the time a second transfer of the data from the shift register to the read buffer is
initiated or an overrun condition will exist. In cases of overrun, the byte which causes the overrun is lost.
A write to the serial peripheral data I/O register is not buffered and places data directly into the shift
register for transmission.
$000C
Bit 7
654321
Bit 0
Read:
SPD7
SPD6
SPD5
SPD4
SPD3
SPD2
SPD1
SPD0
Write:
Reset:
Unaffected by reset
Figure 10-6. PI Data Register (SPDR)
相关PDF资料
PDF描述
VI-B5N-CU-F2 CONVERTER MOD DC/DC 18.5V 200W
MC68HC705C8AVFNE IC MCU 8BIT 44-PLCC
VJ1825Y823JBGAT4X CAP CER 0.082UF 1KV 5% X7R 1825
VI-B5M-CU-F3 CONVERTER MOD DC/DC 10V 200W
MC68HCP11E0FNE IC MCU 8BIT 52-PLCC
相关代理商/技术参数
参数描述
MC68HC705C9AVFNE 功能描述:8位微控制器 -MCU 8B MCU 352 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68HC705E6CDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC705G1B 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705J1A 制造商:Freescale Semiconductor 功能描述:
MC68HC705J1ACDW 功能描述:IC MCU 4MHZ 1.2K OTP 20-SOIC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND